Re: New install


Teton Amateur Radio Repeater Association (TARRA)
 

I don't see any issue with the wiring.

Mick - W7CAT
Node 3464

----- Original Message -----
From: William Phillips
To: IRLP@irlp.groups.io
Sent: Saturday, December 21, 2019 07:26:47 PM
Subject: Re: [IRLP] New install

> The radio connections are as follows
>
> Radio Irlp board
> Pin 2 9
> Pin 3. 2
> Pin 7. 6
> Pin 8. 7
> Pin 11. 8
>
> I have a 10uf capacitor on pin 9 irlp to pin 2 radio. I have radio programmed for cos pin 8 active low and the board matches. I tried another radio I have same issue. I also confirmed this radio works with signalink on an EchoLink I had set up. I have a mike connected with the hangup plate attached.
> > On Dec 21, 2019, at 6:11 PM, Teton Amateur Radio Repeater Association (TARRA) wrote:
> >
> > I would like to know exactly what connections you are using on the radio and on the IRLP board and what is connected to what. It shouldn't be complicated.
> >
> > Keep in mind it doesn't matter what is connected to pin 8 if there isn't a shorting plug in the microphone connector.
> >
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Darin Lehnert
> > To: IRLP@irlp.groups.io
> > Sent: Saturday, December 21, 2019 02:11:59 PM
> > Subject: Re: [IRLP] New install
> >
> > > Hi William,
> > > Is this a 8 channel 16 channel Motorola ? If it is a 16 channel you need to
> > > program
> > > pin 8 on the Motorola to Select PL/DPL & CSQ Detect and active low
> > > You also need to make sure your active low on the IRLP board
> > > and I always use a 10k resistor on the pink side of the sound fob.
> > >
> > > Good Luck !!
> > >
> > > Darin
> > > kc7tig
> > >
> > > On Sat, Dec 21, 2019 at 12:44 PM William Phillips
> > > wrote:
> > >
> > > > Would the audio be a separate issue? Could this be a software issue should
> > > > I try reinstalling?
> > > > > On Dec 21, 2019, at 11:28 AM, Nosey Nick VA3NNW
> > > > wrote:
> > > > >
> > > > > William Phillips wrote:
> > > > >> Pressed : Seen
> > > > >> 1:nothing
> > > > >> 2:3 when released 1
> > > > >> 3:3 when released 1
> > > > >> 4:5 when released 1
> > > > >> 5:5 when released 1
> > > > >> 6:7 when released 1
> > > > >> 7:7 when released 1
> > > > >> 8:9 when released 1
> > > > >> 9:9 when released 1
> > > > >
> > > > > Sounds a lot like DTMF 1 is stuck "high", and adding 1 to otherwise-even
> > > > > numbers.
> > > > >
> > > > > Check (I think) D0 / GPIO 4 / Pin 15 for possible shorts?
> > > > >
> > > > > Nick
> > > > >
> > > > > --
> > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > use Std::Disclaimer; sig@...
> > > > > I checked the Internet to see how long a possum can hold its breath.
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
>
>
>
>
--

Join IRLP@irlp.groups.io to automatically receive all group messages.