Re: New install


William Phillips
 

it looks like the reinstall fixed the audio issue. should the dtmf tones match what is pressed on the radio?

On Dec 21, 2019, at 8:41 PM, Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

I don't see any issue with the wiring.

Mick - W7CAT
Node 3464 

----- Original Message ----- 
From: William Phillips 
To: IRLP@irlp.groups.io 
Sent: Saturday, December 21, 2019 07:26:47 PM 
Subject: Re: [IRLP] New install 

> The radio connections are as follows 
> 
> Radio Irlp board 
> Pin 2 9 
> Pin 3. 2 
> Pin 7. 6 
> Pin 8. 7 
> Pin 11. 8 
> 
> I have a 10uf capacitor on pin 9 irlp to pin 2 radio. I have radio programmed for cos pin 8 active low and the board matches. I tried another radio I have same issue. I also confirmed this radio works with signalink on an EchoLink I had set up. I have a mike connected with the hangup plate attached. 
> > On Dec 21, 2019, at 6:11 PM, Teton Amateur Radio Repeater Association (TARRA) wrote: 
> > 
> > I would like to know exactly what connections you are using on the radio and on the IRLP board and what is connected to what. It shouldn't be complicated. 
> > 
> > Keep in mind it doesn't matter what is connected to pin 8 if there isn't a shorting plug in the microphone connector. 
> > 
> > Mick - W7CAT 
> > Node 3464 
> > 
> > ----- Original Message ----- 
> > From: Darin Lehnert 
> > To: IRLP@irlp.groups.io 
> > Sent: Saturday, December 21, 2019 02:11:59 PM 
> > Subject: Re: [IRLP] New install 
> > 
> > > Hi William, 
> > > Is this a 8 channel 16 channel Motorola ? If it is a 16 channel you need to 
> > > program 
> > > pin 8 on the Motorola to Select PL/DPL & CSQ Detect and active low 
> > > You also need to make sure your active low on the IRLP board 
> > > and I always use a 10k resistor on the pink side of the sound fob. 
> > > 
> > > Good Luck !! 
> > > 
> > > Darin 
> > > kc7tig 
> > > 
> > > On Sat, Dec 21, 2019 at 12:44 PM William Phillips 
> > > wrote: 
> > > 
> > > > Would the audio be a separate issue? Could this be a software issue should 
> > > > I try reinstalling? 
> > > > > On Dec 21, 2019, at 11:28 AM, Nosey Nick VA3NNW 
> > > > wrote: 
> > > > > 
> > > > > William Phillips wrote: 
> > > > >> Pressed : Seen 
> > > > >> 1:nothing 
> > > > >> 2:3 when released 1 
> > > > >> 3:3 when released 1 
> > > > >> 4:5 when released 1 
> > > > >> 5:5 when released 1 
> > > > >> 6:7 when released 1 
> > > > >> 7:7 when released 1 
> > > > >> 8:9 when released 1 
> > > > >> 9:9 when released 1 
> > > > > 
> > > > > Sounds a lot like DTMF 1 is stuck "high", and adding 1 to otherwise-even 
> > > > > numbers. 
> > > > > 
> > > > > Check (I think) D0 / GPIO 4 / Pin 15 for possible shorts? 
> > > > > 
> > > > > Nick 
> > > > > 
> > > > > -- 
> > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209. 
> > > > > use Std::Disclaimer; sig@... 
> > > > > I checked the Internet to see how long a possum can hold its breath. 
> > > > > 
> > > > > 
> > > > > 
> > > > > 
> > > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > 
> > > 
> > > 
> > > 
> > -- 
> > 
> 
> 
> 
> 
-- 


Join IRLP@irlp.groups.io to automatically receive all group messages.