Date   
Re: Kenwood TM-281A with PI-Irlp node

Milt Duquette
 

Good afternoon Ken

Yes the chip looks right and we did the same modes to it

But the COS is always on the irlp even if we change the jumper to high or low   until u physically turn off the radio. The tx light lights up when transmit comes on . When the IRLP node is transmitting it has noise and hum behind it and loud

When I key  the radio it does not turn on the irlp node yellow led for DTMF
The radio works ok by itself.

The Kenwood TM-D710G works great on the irlp levels all ok..

You have any recommendations.  This is a Raspberry Pi/IRLP node I purchase about a year ago.No Computer 



Thanks
 

Milt Duquette

1 (403) 928-1000 (cell)

Web:  http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette



On Jun 29, 2020, at 1:32 PM, Ken Arck <ken@...> wrote:

<20191103_173238.jpg>

Re: Is there something else i need to do for RA to work?

kd1yh
 

10.0.0.10 refused to connect.

-----Original Message-----
From: David Cameron - IRLP
Sent: Monday, June 22, 2020 12:09 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] Is there something else i need to do for RA to work?

redirect points to port 15426, and not sure that the install script does
not use 15426.

When on the local LAN, what do you get when you go to

http://192.168.1.10 (replace with the LAN IP)
or
http://stnxxx.ip.irlp.net (replace xxxx with the node number)

Dave Cameron

On 2020-06-21 7:08 p.m., kd1yh wrote:
Is there something else i need to do for RA to work?
I downloaded the script but cannot get the irlp.net/redirect to work.
Do I need to change a port location / permissions somewhere?
Paul Kd1YH
rebuilding node 4651 /8571 with debian 10.4

Re: Kenwood TM-281A with PI-Irlp node

Ken Arck
 


Hi Milt

Does the attached look right?




At 12:12 PM 6/29/2020, you wrote:
Good afternoon Ken,

Mine has the 12 pin audio amp LA4631 with 2 hold down bolts

Thanks
Â

Milt Duquette

1 (403) 928-1000 (cell)

Web: Â http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette


[]  

On Jun 28, 2020, at 10:25 PM, Ken Arck <ken@... > wrote:

Ahhh OK, I do have the updates for the new audio IC. I'll get them to you tomorrow

Ken


At 07:52 PM 6/28/2020, you wrote:
I have looked at that and we done all that but it is a newer amplifie audio chip.  We have noise in the transmit audio and it doesn’t decode dtmf audio
On Jun 28, 2020, at 7:24 PM, Ken Arck <ken@... > wrote:
 Have a look: https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf Ken At 05:54 PM 6/28/2020, you wrote:
Good afternoon Has anyone hooked a Kenwood TM-281a to pi-irlp node? Is there any suggestions? I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too. Need some help  instead of tying up a Kenwood TM-D710g dual bander. VE6MLD Thanks  Milt Duquette 1 (403) 928-1000 (cell) Web:  http://www.photosbymilt.ca Emails: miltduquette@... Twitter: @milt_duquette
<3a3639d9.jpg>
  Content-Disposition: inline;        filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";  filename*1=.jpg Content-Type: image/jpeg;       x-unix-mode=0666;       name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg" Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>
------------------------------------------------------------------------------ President and CTO - Arcom Controllers Makers of repeater controllers and accessories. https://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave. We we offer complete turn-key repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" []

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]  

Content-Disposition: inline;
         filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";
         filename*1=.jpg
Content-Type: image/jpeg;
         x-unix-mode=0666;
         name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg"
Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Re: Kenwood TM-281A with PI-Irlp node

Milt Duquette
 

Good afternoon Ken,

Mine has the 12 pin audio amp LA4631 with 2 hold down bolts

Thanks
 

Milt Duquette

1 (403) 928-1000 (cell)

Web:  http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette



On Jun 28, 2020, at 10:25 PM, Ken Arck <ken@...> wrote:

Ahhh OK, I do have the updates for the new audio IC. I'll get them to you tomorrow

Ken


At 07:52 PM 6/28/2020, you wrote:
I have looked at that and we done all that but it is a newer amplifie audio chip.  We have noise in the transmit audio and it doesn’t decode dtmf audio
On Jun 28, 2020, at 7:24 PM, Ken Arck <ken@...> wrote:
 Have a look: https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf Ken At 05:54 PM 6/28/2020, you wrote:
Good afternoon Has anyone hooked a Kenwood TM-281a to pi-irlp node? Is there any suggestions? I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too. Need some help  instead of tying up a Kenwood TM-D710g dual bander. VE6MLD Thanks  Milt Duquette 1 (403) 928-1000 (cell) Web:  http://www.photosbymilt.ca Emails: miltduquette@... Twitter: @milt_duquette
<3a3639d9.jpg>
  Content-Disposition: inline;          filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";  filename*1=.jpg Content-Type: image/jpeg;       x-unix-mode=0666;       name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg" Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>
------------------------------------------------------------------------------ President and CTO - Arcom Controllers Makers of repeater controllers and accessories. https://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave. We we offer complete turn-key repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" []

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Re: No audio from home

Carl Sorensen
 

Hi Everyone,

It has been a few weeks since I posted last.  I was surprised I haven't heard anything.  My Node #3417 is still not sending audio.  It had worked until recently.  Still able to connect through the DTMF however no Audio is going out.  Audio is still coming in when connected to another node.

Carl, NB7C
nodes 3417 and 3407

On Tuesday, June 16, 2020, 7:17:05 PM MDT, Carl Sorensen via groups.io <carlnb7c@...> wrote:


Hi Dave,

You and I updated this embedded node (#3417) recently after we set up the PI node (#3407) earlier this year (maybe this past Fall). We did this because we had trouble with my Internet Provider having an additional Port blockage.  We set it up to use a VPN.  They worked well together and I do not know when the home audio stopped working.

I didn't see a "Capture" setting on this version.  I do remember a "CAPTURE" setting before we updated it.

Carl NB7C

On Tuesday, June 16, 2020, 6:25:46 PM MDT, David Cameron - IRLP <dcameron@...> wrote:


Where is the "CAPTURE" set? What version of embedded node is this?
Depending on the version it should be set for Front Mic or Back Mic.

Dave Cameron

On 2020-06-16 5:13 p.m., Carl Sorensen via groups.io wrote:
> Mic is set at 54.  Line is 47.
>
> Is there anything I should look at?
>
> Carl NB7C
>
> On Tuesday, June 16, 2020, 4:03:20 PM MDT, David Cameron - IRLP
> <dcameron@...> wrote:
>
>
> Do the people hear a dead transmission (it starts to transmit but has no
> audio) or nothing at all?
>
> Have you looked at the mixer settings?
>
> Dave Cameron
> VE7LTD
>
> On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
>  > Hi Guys,
>  > I discovered my embedded node (#3417) wasn't putting out audio.  The
>  > DTMF is working fine.  I can connect but not heard.  Audio coming back
>  > sounds great but I can't be heard.
>  >
>  > I did the troubleshoot and it said everything passed except #10, the
>  > enviromental files.
>  >
>  > My PI node is working great (#3407)
>  >
>  > Carl Sorensen, NB7C
>  >
>
>
>


Re: Kenwood TM-281A with PI-Irlp node

Ken Arck
 

Ahhh OK, I do have the updates for the new audio IC. I'll get them to you tomorrow

Ken


At 07:52 PM 6/28/2020, you wrote:
I have looked at that and we done all that but it is a newer amplifie audio chip.  We have noise in the transmit audio and it doesn’t decode dtmf audio
On Jun 28, 2020, at 7:24 PM, Ken Arck <ken@...> wrote:
 Have a look: https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf Ken At 05:54 PM 6/28/2020, you wrote:
Good afternoon Has anyone hooked a Kenwood TM-281a to pi-irlp node? Is there any suggestions? I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too. Need some help  instead of tying up a Kenwood TM-D710g dual bander. VE6MLD Thanks  Milt Duquette 1 (403) 928-1000 (cell) Web:  http://www.photosbymilt.ca Emails: miltduquette@... Twitter: @milt_duquette
<3a3639d9.jpg>
  Content-Disposition: inline;          filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";  filename*1=.jpg Content-Type: image/jpeg;       x-unix-mode=0666;       name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg" Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>
------------------------------------------------------------------------------ President and CTO - Arcom Controllers Makers of repeater controllers and accessories. https://www.arcomcontrollers.com/ Authorized Dealers for Kenwood and Telewave. We we offer complete turn-key repeater packages! AH6LE/R - IRLP Node 3000 http://www.irlp.net "We don't just make 'em. We use 'em!" []
------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Re: Kenwood TM-281A with PI-Irlp node

Milt Duquette
 

We spent three days on it


On Jun 28, 2020, at 8:52 PM, Milt Duquette <miltduquette@...> wrote:

I have looked at that and we done all that but it is a newer amplifie audio chip.  We have noise in the transmit audio and it doesn’t decode dtmf audio


On Jun 28, 2020, at 7:24 PM, Ken Arck <ken@...> wrote:

 Have a look:

https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf

Ken



At 05:54 PM 6/28/2020, you wrote:
Good afternoon

Has anyone hooked a Kenwood TM-281a to pi-irlp node?
Is there any suggestions?

I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too.

Need some help  instead of tying up a Kenwood TM-D710g dual bander.


VE6MLD

Thanks
Â

Milt Duquette

1 (403) 928-1000 (cell)

Web: Â http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette


<3a3639d9.jpg>
 

Content-Disposition: inline;
         filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";
         filename*1=.jpg
Content-Type: image/jpeg;
         x-unix-mode=0666;
         name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg"
Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Re: Kenwood TM-281A with PI-Irlp node

Milt Duquette
 

I have looked at that and we done all that but it is a newer amplifie audio chip.  We have noise in the transmit audio and it doesn’t decode dtmf audio


On Jun 28, 2020, at 7:24 PM, Ken Arck <ken@...> wrote:

 Have a look:

https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf

Ken



At 05:54 PM 6/28/2020, you wrote:
Good afternoon

Has anyone hooked a Kenwood TM-281a to pi-irlp node?
Is there any suggestions?

I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too.

Need some help  instead of tying up a Kenwood TM-D710g dual bander.


VE6MLD

Thanks
Â

Milt Duquette

1 (403) 928-1000 (cell)

Web: Â http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette


<3a3639d9.jpg>
 

Content-Disposition: inline;
         filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";
         filename*1=.jpg
Content-Type: image/jpeg;
         x-unix-mode=0666;
         name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg"
Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Re: Kenwood TM-281A with PI-Irlp node

Ken Arck
 

Have a look:

https://www.arcomcontrollers.com/documents/rc210/tm-281a_mod.pdf

Ken



At 05:54 PM 6/28/2020, you wrote:
Good afternoon

Has anyone hooked a Kenwood TM-281a to pi-irlp node?
Is there any suggestions?

I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too.

Need some help  instead of tying up a Kenwood TM-D710g dual bander.


VE6MLD

Thanks
Â

Milt Duquette

1 (403) 928-1000 (cell)

Web: Â http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette


[]  

Content-Disposition: inline;
         filename*0="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175";
         filename*1=.jpg
Content-Type: image/jpeg;
         x-unix-mode=0666;
         name="Milt's Overlay Logo - Black on White 1 x1-1-Quick Preset_175x175.jpg"
Content-Id: <F454BFEC-8875-4A6F-B8FE-1FAF1B20150B>

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories.
https://www.arcomcontrollers.com/
Authorized Dealers for Kenwood and Telewave.
We we offer complete turn-key repeater packages!
AH6LE/R - IRLP Node 3000
http://www.irlp.net
"We don't just make 'em. We use 'em!"
[]

Kenwood TM-281A with PI-Irlp node

Milt Duquette
 

Good afternoon

Has anyone hooked a Kenwood TM-281a to pi-irlp node?
Is there any suggestions?

I have a DB9 female cable and hole drilled into back of of the radicand got the pinout of db9 too.

Need some help  instead of tying up a Kenwood TM-D710g dual bander.


VE6MLD

Thanks
 

Milt Duquette

1 (403) 928-1000 (cell)

Web:  http://www.photosbymilt.ca

Emails:

miltduquette@...

Twitter: @milt_duquette



Re: Is there something else i need to do for RA to work?

kd1yh
 

norm ""http://10.0.0.11:15426/control/index.php"


http://10.0.0.94:15426/control/index.php
10.0.0.94 refused to connect.

Where does " 15426" authenticate from?
kd1yh node 4651

-----Original Message-----
From: David Cameron - IRLP
Sent: Monday, June 22, 2020 12:09 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] Is there something else i need to do for RA to work?

redirect points to port 15426, and not sure that the install script does
not use 15426.

When on the local LAN, what do you get when you go to

http://192.168.1.10 (replace with the LAN IP)
or
http://stnxxx.ip.irlp.net (replace xxxx with the node number)

Dave Cameron

On 2020-06-21 7:08 p.m., kd1yh wrote:
Is there something else i need to do for RA to work?
I downloaded the script but cannot get the irlp.net/redirect to work.
Do I need to change a port location / permissions somewhere?
Paul Kd1YH
rebuilding node 4651 /8571 with debian 10.4

Re: Is there something else i need to do for RA to work?

kd1yh
 

it cannot find so I think it is port thinh but where?

-----Original Message-----
From: David Cameron - IRLP
Sent: Monday, June 22, 2020 12:09 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] Is there something else i need to do for RA to work?

redirect points to port 15426, and not sure that the install script does
not use 15426.

When on the local LAN, what do you get when you go to

http://192.168.1.10 (replace with the LAN IP)
or
http://stnxxx.ip.irlp.net (replace xxxx with the node number)

Dave Cameron

On 2020-06-21 7:08 p.m., kd1yh wrote:
Is there something else i need to do for RA to work?
I downloaded the script but cannot get the irlp.net/redirect to work.
Do I need to change a port location / permissions somewhere?
Paul Kd1YH
rebuilding node 4651 /8571 with debian 10.4

Re: Is there something else i need to do for RA to work?

David Cameron - IRLP
 

redirect points to port 15426, and not sure that the install script does not use 15426.

When on the local LAN, what do you get when you go to

http://192.168.1.10 (replace with the LAN IP)
or
http://stnxxx.ip.irlp.net (replace xxxx with the node number)

Dave Cameron

On 2020-06-21 7:08 p.m., kd1yh wrote:
Is there something else i need to do for RA to work?
I downloaded the script but cannot get the irlp.net/redirect to work.
Do I need to change a port location / permissions somewhere?
Paul Kd1YH
rebuilding node 4651 /8571 with debian 10.4

Is there something else i need to do for RA to work?

kd1yh
 

 
 
 
Is there something else i need to do for RA to work?
I downloaded the script but cannot get the irlp.net/redirect to work.
Do I need to change a port location / permissions somewhere?
 
Paul Kd1YH
rebuilding node 4651 /8571 with debian 10.4

Re: No audio from home

Carl Sorensen
 

Hi Dave,

You and I updated this embedded node (#3417) recently after we set up the PI node (#3407) earlier this year (maybe this past Fall). We did this because we had trouble with my Internet Provider having an additional Port blockage.  We set it up to use a VPN.  They worked well together and I do not know when the home audio stopped working.

I didn't see a "Capture" setting on this version.  I do remember a "CAPTURE" setting before we updated it.

Carl NB7C

On Tuesday, June 16, 2020, 6:25:46 PM MDT, David Cameron - IRLP <dcameron@...> wrote:


Where is the "CAPTURE" set? What version of embedded node is this?
Depending on the version it should be set for Front Mic or Back Mic.

Dave Cameron

On 2020-06-16 5:13 p.m., Carl Sorensen via groups.io wrote:
> Mic is set at 54.  Line is 47.
>
> Is there anything I should look at?
>
> Carl NB7C
>
> On Tuesday, June 16, 2020, 4:03:20 PM MDT, David Cameron - IRLP
> <dcameron@...> wrote:
>
>
> Do the people hear a dead transmission (it starts to transmit but has no
> audio) or nothing at all?
>
> Have you looked at the mixer settings?
>
> Dave Cameron
> VE7LTD
>
> On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
>  > Hi Guys,
>  > I discovered my embedded node (#3417) wasn't putting out audio.  The
>  > DTMF is working fine.  I can connect but not heard.  Audio coming back
>  > sounds great but I can't be heard.
>  >
>  > I did the troubleshoot and it said everything passed except #10, the
>  > enviromental files.
>  >
>  > My PI node is working great (#3407)
>  >
>  > Carl Sorensen, NB7C
>  >
>
>
>


Re: No audio from home

David Cameron - IRLP
 

Where is the "CAPTURE" set? What version of embedded node is this? Depending on the version it should be set for Front Mic or Back Mic.

Dave Cameron

On 2020-06-16 5:13 p.m., Carl Sorensen via groups.io wrote:
Mic is set at 54.  Line is 47.
Is there anything I should look at?
Carl NB7C
On Tuesday, June 16, 2020, 4:03:20 PM MDT, David Cameron - IRLP <dcameron@...> wrote:
Do the people hear a dead transmission (it starts to transmit but has no
audio) or nothing at all?
Have you looked at the mixer settings?
Dave Cameron
VE7LTD
On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
> Hi Guys,
> I discovered my embedded node (#3417) wasn't putting out audio.  The
> DTMF is working fine.  I can connect but not heard.  Audio coming back
> sounds great but I can't be heard.
>
> I did the troubleshoot and it said everything passed except #10, the
> enviromental files.
>
> My PI node is working great (#3407)
>
> Carl Sorensen, NB7C
>

Re: No audio from home

Carl Sorensen
 

Mic is set at 54.  Line is 47.

Is there anything I should look at?

Carl NB7C

On Tuesday, June 16, 2020, 4:03:20 PM MDT, David Cameron - IRLP <dcameron@...> wrote:


Do the people hear a dead transmission (it starts to transmit but has no
audio) or nothing at all?

Have you looked at the mixer settings?

Dave Cameron
VE7LTD

On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
> Hi Guys,
> I discovered my embedded node (#3417) wasn't putting out audio.  The
> DTMF is working fine.  I can connect but not heard.  Audio coming back
> sounds great but I can't be heard.
>
> I did the troubleshoot and it said everything passed except #10, the
> enviromental files.
>
> My PI node is working great (#3407)
>
> Carl Sorensen, NB7C
>


Re: No audio from home

Carl Sorensen
 

Yes, it transmits a carrier, no audio. I hate to say it, but I didn't think about the mixer. Since it worked well before, I didn't think anything as would have changed.

Carl, NB7C

On Tuesday, June 16, 2020, 04:03:20 PM MDT, David Cameron - IRLP <dcameron@...> wrote:


Do the people hear a dead transmission (it starts to transmit but has no
audio) or nothing at all?

Have you looked at the mixer settings?

Dave Cameron
VE7LTD

On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
> Hi Guys,
> I discovered my embedded node (#3417) wasn't putting out audio.  The
> DTMF is working fine.  I can connect but not heard.  Audio coming back
> sounds great but I can't be heard.
>
> I did the troubleshoot and it said everything passed except #10, the
> enviromental files.
>
> My PI node is working great (#3407)
>
> Carl Sorensen, NB7C
>


Re: No audio from home

David Cameron - IRLP
 

Do the people hear a dead transmission (it starts to transmit but has no audio) or nothing at all?

Have you looked at the mixer settings?

Dave Cameron
VE7LTD

On 2020-06-16 10:00 a.m., Carl Sorensen via groups.io wrote:
Hi Guys,
I discovered my embedded node (#3417) wasn't putting out audio.  The DTMF is working fine.  I can connect but not heard.  Audio coming back sounds great but I can't be heard.
I did the troubleshoot and it said everything passed except #10, the enviromental files.
My PI node is working great (#3407)
Carl Sorensen, NB7C

No audio from home

Carl Sorensen
 

Hi Guys,
I discovered my embedded node (#3417) wasn't putting out audio.  The DTMF is working fine.  I can connect but not heard.  Audio coming back sounds great but I can't be heard.

I did the troubleshoot and it said everything passed except #10, the enviromental files.

My PI node is working great (#3407)

Carl Sorensen, NB7C