1. IRLP@irlp.groups.io
   Date   
Re: Getting Into IRLP

Jeff Daugherty
 

Www.irlp.net



Sent from my Sprint Phone.


-------- Original message --------
From: "michal.gordon via groups.io" <michal.gordon@...>
Date: 11/19/20 9:56 PM (GMT-07:00)
To: IRLP@irlp.groups.io
Subject: [IRLP] Getting Into IRLP

Hi everyone. 
I'm looking in getting into IRLP. Any thoughts or tips on how to go about it?
 
Thanks, 
Michal
Re: Getting Into IRLP

larry_n7fm
 

Michal,

Depending on what your actual intended use is you can BUY A Raspberry Pi IRLP (turn Key) Node from the Link below.

<http://www.irlp.net/order.html>;

I'm sure Dave Cameron would answer any question and help you if you ask.

Should you be a tinkerer. You can also construct you own by buying the interface board and optional parts from the same link, as well as other optional parts. Or if you have some of the parts already, you can use them. Occasionally you may find a used IRLP Node for sale on some of the other VOIP groups if you happen to subscribe/monitor any of those such as Allstar, Echolink, Hamvoip.

If totally unfamiliar with IRLP you should do some googling and read about how it all works. Perhaps there are nodes in your locale that you might use and evaluate if some IRLP equipped repeater may do do for you what you want or at least help you decide if you truly need/want your own personal node. Also you will need to provide an RF radio to hook the IRLP node to.

IRLP is an RF to RF based system. Meaning RF input passes via VOIP on the INTERNET to an RF output on the opposite end. which will require you to use an RF Transceiver to be its input/output connection for a NODE.
An additional cost if you don't already have a radio system to hook IRLP to.

If more questions --> larry@n7fm.com

Good Luck
Larry - N7FM

On 11/19/20 7:40 PM, michal.gordon via groups.io wrote:
Hi everyone.
I'm looking in getting into IRLP. Any thoughts or tips on how to go about it?
Thanks,
Michal
Getting Into IRLP

michal.gordon@...
 

Hi everyone. 
I'm looking in getting into IRLP. Any thoughts or tips on how to go about it?
 
Thanks, 
Michal
Re: SpaceX Crew-1 Mission audio

Jeff
 

Audio sounded great here! Thanks guys!

Jeff & Erik
WB8REI & N8XHZ

On Nov 15, 2020, at 4:30 PM, k9dc via groups.io <Dave=dcg.us@groups.io> wrote:


We are attempting to carry the SpaceX Crew-1 Launch audio on Reflector 9601. Presumably we found a feed with no commentary or advertising, thus it is largely silent.

Warning: It may not be possible for simplex node operators, or repeaters without the ability to disconnect during a transmission, to disconnect during long periods of activity. So use caution. We take no responsibility for looking up anyone’s repeater.

Launch is scheduled for roughly 00:27 UTC or 19:27 EST.

-k9dc
Re: SpaceX Crew-1 Mission audio

Dave K9DC
 

It’s not exactly Ham type traffic, where folks talk about nothing for hours, heheh

-k9dc

On Nov 15, 2020, at 22:20, Jeff Daugherty <w0nwa@cox.net> wrote:

There was quite a long pause when I wrote this. But working fine. Thanks for the feed!!



Sent from my Sprint Phone.


-------- Original message --------
From: "k9dc via groups.io" <Dave=dcg.us@groups.io>
Date: 11/15/20 8:03 PM (GMT-07:00)
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio


Still chattering at 2200 eastern

-k9dc
Re: SpaceX Crew-1 Mission audio

Jeff Daugherty
 

There was quite a long pause when I wrote this. But working fine. Thanks for the feed!!



Sent from my Sprint Phone.


-------- Original message --------
From: "k9dc via groups.io" <Dave@...>
Date: 11/15/20 8:03 PM (GMT-07:00)
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio


Still chattering at 2200 eastern

-k9dc

> On Nov 15, 2020, at 20:57, Jeff Daugherty <w0nwa@...> wrote:
>
> Anyone know if the feed is still up? Pretty quiet.
>
>
>
> Jeff
>
> W0NWA
>
>
>
> Sent from Mail for Windows 10
>
>
>
> From: David Cameron - IRLP
> Sent: Sunday, November 15, 2020 3:34 PM
> To: IRLP@irlp.groups.io
> Subject: Re: [IRLP] SpaceX Crew-1 Mission audio
>
>
>
> I
>
>
>
>






Re: SpaceX Crew-1 Mission audio

Dave K9DC
 

Still chattering at 2200 eastern

-k9dc

On Nov 15, 2020, at 20:57, Jeff Daugherty <w0nwa@cox.net> wrote:

Anyone know if the feed is still up? Pretty quiet.



Jeff

W0NWA



Sent from Mail for Windows 10



From: David Cameron - IRLP
Sent: Sunday, November 15, 2020 3:34 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio



I
Re: SpaceX Crew-1 Mission audio

Benton Holzwarth
 

On 2020-11-15 17:57, Jeff Daugherty wrote:

Anyone know if the feed is still up? Pretty quiet.

It's still active right this moment.  18:42 PT.  Maybe your mode or repeater timed out?

Thanks, Daves for making this available.  Great audio quality.

Benton 15nov20
--
stn 7665
NX7O
benton@...
Re: SpaceX Crew-1 Mission audio

Jeff Daugherty
 

Anyone know if the feed is still up? Pretty quiet.

 

Jeff

W0NWA

 

Sent from Mail for Windows 10

 

From: David Cameron - IRLP
Sent: Sunday, November 15, 2020 3:34 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio

 

I

 
Re: SpaceX Crew-1 Mission audio

David Cameron - IRLP
 

I think the feed we are using stops once they dock. It is a manual process on this end, but I will attempt to keep it up and working as long as I can.

The audio is now running through an Auto-gain control, so hopefully it will not get too loud at some point. People tend to get excited when the liftoff occurs. But it sounds like they had to reopen some hatch, so I am thinking this one may be a scrub anyhow.

Dave Cameron

On 15/11/2020 2:31 p.m., Jeff Daugherty wrote:

Seems to work now. Also will the feed be up for the whole mission or just lift off?

Jeff

W0NWA

Node 4243

Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986>; for Windows 10

*From: *David Cameron - IRLP <mailto:dcameron@irlp.net>
*Sent: *Sunday, November 15, 2020 3:15 PM
*To: *IRLP@irlp.groups.io <mailto:IRLP@irlp.groups.io>
*Subject: *Re: [IRLP] SpaceX Crew-1 Mission audio

W
Re: SpaceX Crew-1 Mission audio

Jeff Daugherty
 

Seems to work now. Also will the feed be up for the whole mission or just lift off?

 

Jeff

W0NWA

Node 4243

 

Sent from Mail for Windows 10

 

From: David Cameron - IRLP
Sent: Sunday, November 15, 2020 3:15 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio

 

W

 
Re: SpaceX Crew-1 Mission audio

David Cameron - IRLP
 

We have no control over the audio level that the feed has, and that is echoed in the audio level heard on the radio.
That is as loud as I can make it currently. I will try to use a different feed method, but if the audio all of a sudden gets loud, I will be overdriving every node out there too.

Dave Cameron

On 15/11/2020 2:04 p.m., Jeff Daugherty wrote:
Feed audio issues? Audio low.
Better then nothing :)





Sent from my Sprint Phone.


-------- Original message --------
From: "k9dc via groups.io" <Dave=dcg.us@groups.io>
Date: 11/15/20 2:49 PM (GMT-07:00)
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio


It is today (figured everyone one that, sorry)

-k9dc

On Nov 15, 2020, at 16:44, Jeff Daugherty <w0nwa@cox.net> wrote:

What is the date of the launch? The times are listed.

Jeff
W0NWA
Node 4243
Re: SpaceX Crew-1 Mission audio

Jeff Daugherty
 

Feed audio issues? Audio low. 
Better then nothing :)





Sent from my Sprint Phone.


-------- Original message --------
From: "k9dc via groups.io" <Dave@...>
Date: 11/15/20 2:49 PM (GMT-07:00)
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] SpaceX Crew-1 Mission audio


It is today (figured everyone one that, sorry)

-k9dc

> On Nov 15, 2020, at 16:44, Jeff Daugherty <w0nwa@...> wrote:
>
> What is the date of the launch? The times are listed.
> 
> Jeff
> W0NWA
> Node 4243
Re: SpaceX Crew-1 Mission audio

Dave K9DC
 

It is today (figured everyone one that, sorry)

-k9dc

On Nov 15, 2020, at 16:44, Jeff Daugherty <w0nwa@cox.net> wrote:

What is the date of the launch? The times are listed.

Jeff
W0NWA
Node 4243
Re: SpaceX Crew-1 Mission audio

Jeff Daugherty
 

What is the date of the launch? The times are listed.

 

Jeff

W0NWA

Node 4243

 

Sent from Mail for Windows 10

 

From: k9dc via groups.io
Sent: Sunday, November 15, 2020 2:34 PM
To: IRLP@irlp.groups.io
Subject: [IRLP] SpaceX Crew-1 Mission audio

 

 

 

 
SpaceX Crew-1 Mission audio

Dave K9DC
 

We are attempting to carry the SpaceX Crew-1 Launch audio on Reflector 9601. Presumably we found a feed with no commentary or advertising, thus it is largely silent.

Warning: It may not be possible for simplex node operators, or repeaters without the ability to disconnect during a transmission, to disconnect during long periods of activity. So use caution. We take no responsibility for looking up anyone’s repeater.

Launch is scheduled for roughly 00:27 UTC or 19:27 EST.

-k9dc
Re: cannot get irlp CON screen up

Trevor Wood
 

Many thanks for your help managed to reset things and up and running cheers Paul  and fred.
Appreciated for the help and your time.
Trevor M0TWS

On Sat, 14 Nov 2020 at 00:18, kd1yh <kd1yh@...> wrote:
Trevor,
 
root@stn4651:~#  /var/www/irlpvutil/remove_pwd
 
#################################################
IRLPvCON Password Protection Has Been Removed
#################################################
 
 
go to admin page and put in your info.
image
 
kd1yh node 4651 Paul
 
From: Fred via groups.io
Sent: Friday, November 13, 2020 5:55 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up
 

Trevor,

    Just copy and paste this in a putty session.  It will remove the user name and password for vcon and you can start over and put a new one on it.          /var/www/irlpvutil/remove_pwd        

 

From: Trevor Wood
Sent: Friday, November 13, 2020 4:42 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up

 

Hi again ok, got the MON screen on but it when i try t log into the CON screen

this is were its asking for my password etc this is the one am unable to get into

my password is correct it was all written down hi in my black book when it was first set up.

sorry if I miss interpreted the situation paul.

trevor m0tws

 

On Fri, 13 Nov 2020 at 19:55, kd1yh <kd1yh@...> wrote:

Trevor,

 

Putty is just for root and repeater logging,

 

vcon and vmon are webservers/

 

 

So with Putty,  stn5005.ip.irlp.net with your port i.e. 22 (don’t use that!!)

You will be able to use as though you was in front of the console.

 

Vcon, Vmon are web based through your server on your computer

(10.0.0.xx:15426/irlpvmon/)

brings up from inside the firewall.

/var/www/irlpvutil

in this location. is

remove_pwd

 

but if your router is set up properly vmon should work with no password

 

So your webserver  has a issue.

http://stn8433.ip.irlp.net:15426/irlpvmon    is the Fitchburg node, which is connected to node 9122

 

 

 

From: Trevor Wood

Sent: Friday, November 13, 2020 1:21 PM

Subject: Re: [IRLP] cannot get irlp CON screen up

 

HI Paul the pirlp I can access it using putty on my lan side and it is plugged into a bigger hp router never had enough

with the x4 ports on my router that was supplied from my service supplier for the internet.

so the node works fine and the echo reflector comes back with audio tests no problem.

I have used the con screen since i have had the node but now it will not accept my password and root as login. it use to

so thats when i logged in using my putty software and that accepted my root login and password.

Trevor M0TWS

 

On Fri, 13 Nov 2020 at 14:45, <kd1yh@...> wrote:

http://10.0.0.xxx:15426/control/index.php
Does this work from inside your router local?
node 5005 does not seem to have RA porting correct.
kd1yh node 4651 paul

 
Re: cannot get irlp CON screen up

kd1yh
 

Trevor,
 
root@stn4651:~#  /var/www/irlpvutil/remove_pwd
 
#################################################
IRLPvCON Password Protection Has Been Removed
#################################################
 
 
go to admin page and put in your info.
image
 
kd1yh node 4651 Paul
 

From: Fred via groups.io
Sent: Friday, November 13, 2020 5:55 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up
 

Trevor,

    Just copy and paste this in a putty session.  It will remove the user name and password for vcon and you can start over and put a new one on it.          /var/www/irlpvutil/remove_pwd        

 

From: Trevor Wood
Sent: Friday, November 13, 2020 4:42 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up

 

Hi again ok, got the MON screen on but it when i try t log into the CON screen

this is were its asking for my password etc this is the one am unable to get into

my password is correct it was all written down hi in my black book when it was first set up.

sorry if I miss interpreted the situation paul.

trevor m0tws

 

On Fri, 13 Nov 2020 at 19:55, kd1yh <kd1yh@...> wrote:

Trevor,

 

Putty is just for root and repeater logging,

 

vcon and vmon are webservers/

 

 

So with Putty,  stn5005.ip.irlp.net with your port i.e. 22 (don’t use that!!)

You will be able to use as though you was in front of the console.

 

Vcon, Vmon are web based through your server on your computer

(10.0.0.xx:15426/irlpvmon/)

brings up from inside the firewall.

/var/www/irlpvutil

in this location. is

remove_pwd

 

but if your router is set up properly vmon should work with no password

 

So your webserver  has a issue.

http://stn8433.ip.irlp.net:15426/irlpvmon    is the Fitchburg node, which is connected to node 9122

 

 

 

From: Trevor Wood

Sent: Friday, November 13, 2020 1:21 PM

To: IRLP@irlp.groups.io

Subject: Re: [IRLP] cannot get irlp CON screen up

 

HI Paul the pirlp I can access it using putty on my lan side and it is plugged into a bigger hp router never had enough

with the x4 ports on my router that was supplied from my service supplier for the internet.

so the node works fine and the echo reflector comes back with audio tests no problem.

I have used the con screen since i have had the node but now it will not accept my password and root as login. it use to

so thats when i logged in using my putty software and that accepted my root login and password.

Trevor M0TWS

 

On Fri, 13 Nov 2020 at 14:45, <kd1yh@...> wrote:

http://10.0.0.xxx:15426/control/index.php
Does this work from inside your router local?
node 5005 does not seem to have RA porting correct.
kd1yh node 4651 paul

 
Re: cannot get irlp CON screen up

Trevor Wood
 

fred the putty screen at the top i put in my lan address presume the copy paste line you sent me to reset password is pasted into the session box and saved ???
trevor

On Fri, 13 Nov 2020 at 22:58, Trevor Wood via groups.io <irlp5852=gmail.com@groups.io> wrote:
Cheers fred i will try that appreciated.
trevor m0tws

On Fri, 13 Nov 2020 at 22:55, Fred via groups.io <w5mgm=aol.com@groups.io> wrote:

Trevor,

    Just copy and paste this in a putty session.  It will remove the user name and password for vcon and you can start over and put a new one on it.          /var/www/irlpvutil/remove_pwd        

 

From: Trevor Wood
Sent: Friday, November 13, 2020 4:42 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up

 

Hi again ok, got the MON screen on but it when i try t log into the CON screen

this is were its asking for my password etc this is the one am unable to get into 

my password is correct it was all written down hi in my black book when it was first set up.

sorry if I miss interpreted the situation paul.

trevor m0tws 

 

On Fri, 13 Nov 2020 at 19:55, kd1yh <kd1yh@...> wrote:

Trevor,

 

Putty is just for root and repeater logging,

 

vcon and vmon are webservers/

 

 

So with Putty,  stn5005.ip.irlp.net with your port i.e. 22 (don’t use that!!)

You will be able to use as though you was in front of the console.

 

Vcon, Vmon are web based through your server on your computer

(10.0.0.xx:15426/irlpvmon/)

brings up from inside the firewall.

/var/www/irlpvutil

in this location. is

remove_pwd

 

but if your router is set up properly vmon should work with no password

 

So your webserver  has a issue.

http://stn8433.ip.irlp.net:15426/irlpvmon    is the Fitchburg node, which is connected to node 9122

 

 

 

From: Trevor Wood

Sent: Friday, November 13, 2020 1:21 PM

Subject: Re: [IRLP] cannot get irlp CON screen up

 

HI Paul the pirlp I can access it using putty on my lan side and it is plugged into a bigger hp router never had enough

with the x4 ports on my router that was supplied from my service supplier for the internet.

so the node works fine and the echo reflector comes back with audio tests no problem.

I have used the con screen since i have had the node but now it will not accept my password and root as login. it use to

so thats when i logged in using my putty software and that accepted my root login and password.

Trevor M0TWS

 

On Fri, 13 Nov 2020 at 14:45, <kd1yh@...> wrote:

http://10.0.0.xxx:15426/control/index.php
Does this work from inside your router local?
node 5005 does not seem to have RA porting correct.
kd1yh node 4651 paul

 
Re: cannot get irlp CON screen up

Trevor Wood
 

Cheers fred i will try that appreciated.
trevor m0tws

On Fri, 13 Nov 2020 at 22:55, Fred via groups.io <w5mgm=aol.com@groups.io> wrote:

Trevor,

    Just copy and paste this in a putty session.  It will remove the user name and password for vcon and you can start over and put a new one on it.          /var/www/irlpvutil/remove_pwd        

 

From: Trevor Wood
Sent: Friday, November 13, 2020 4:42 PM
To: IRLP@irlp.groups.io
Subject: Re: [IRLP] cannot get irlp CON screen up

 

Hi again ok, got the MON screen on but it when i try t log into the CON screen

this is were its asking for my password etc this is the one am unable to get into 

my password is correct it was all written down hi in my black book when it was first set up.

sorry if I miss interpreted the situation paul.

trevor m0tws 

 

On Fri, 13 Nov 2020 at 19:55, kd1yh <kd1yh@...> wrote:

Trevor,

 

Putty is just for root and repeater logging,

 

vcon and vmon are webservers/

 

 

So with Putty,  stn5005.ip.irlp.net with your port i.e. 22 (don’t use that!!)

You will be able to use as though you was in front of the console.

 

Vcon, Vmon are web based through your server on your computer

(10.0.0.xx:15426/irlpvmon/)

brings up from inside the firewall.

/var/www/irlpvutil

in this location. is

remove_pwd

 

but if your router is set up properly vmon should work with no password

 

So your webserver  has a issue.

http://stn8433.ip.irlp.net:15426/irlpvmon    is the Fitchburg node, which is connected to node 9122

 

 

 

From: Trevor Wood

Sent: Friday, November 13, 2020 1:21 PM

Subject: Re: [IRLP] cannot get irlp CON screen up

 

HI Paul the pirlp I can access it using putty on my lan side and it is plugged into a bigger hp router never had enough

with the x4 ports on my router that was supplied from my service supplier for the internet.

so the node works fine and the echo reflector comes back with audio tests no problem.

I have used the con screen since i have had the node but now it will not accept my password and root as login. it use to

so thats when i logged in using my putty software and that accepted my root login and password.

Trevor M0TWS

 

On Fri, 13 Nov 2020 at 14:45, <kd1yh@...> wrote:

http://10.0.0.xxx:15426/control/index.php
Does this work from inside your router local?
node 5005 does not seem to have RA porting correct.
kd1yh node 4651 paul

 
261 - 280 of 78242  
More
Home Messages Hashtags Subgroups About Features Pricing Updates Terms Help Twitter