Date   
Re: Wired to Wireless on AT Computer

John
 

Can you ping irlp.net from the node console, may need root, not sure?

John @ 6163

On 11/01/2020 2:48:18 PM, Bob Redoutey N5KF (redoutey@...) wrote:
Hi John,
I rebooted the IRLP, all port forward information I had put in the router I
removed, and left only the DMZ setup, and it started working. Still get a
DNS error, not sure why...but good for now.
Thanks for everybody's help!
Bob N5KF
Node 3437
Georgetown TX
On Fri, Jan 10, 2020, 9:59 PM John <gielisj@...> wrote:

Have you RE booted both router and irlp, Bob?

John @ 6163

On 11/01/2020 1:39:26 PM, Bob Redoutey N5KF (redoutey@...) wrote:
The troubleshooting script still gives the same errors.
Somewhere I am not getting it set right....ugh!

Bob N5KF

Ps...sorry for all the bandwidth on this issue.

On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association
(TARRA) <tarra@...> wrote:

Log into your IRLP computer and run the command ifconfig Look for
this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.8.168 netmask 255.255.255.0 broadcast 192.168.8.255

The inet will

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Hi John,

I rebooted the IRLP, all port forward information I had put in the router I removed, and left only the DMZ setup, and it started working.  Still get a DNS error, not sure why...but good for now.

Thanks for everybody's help!

Bob N5KF 
Node 3437
Georgetown TX 

On Fri, Jan 10, 2020, 9:59 PM John <gielisj@...> wrote:
Have you RE booted both router and irlp, Bob?

John @ 6163

> On 11/01/2020 1:39:26 PM, Bob Redoutey N5KF (redoutey@...) wrote:
> > The troubleshooting script still gives the same errors.
>
> Somewhere I am not getting it set right....ugh!
>
> Bob N5KF
>
> Ps...sorry for all the bandwidth on this issue.
>
> On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association
> (TARRA) <tarra@...> wrote:
>
> > Log into your IRLP computer and run the command    ifconfig  Look for this:
> >
> > wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
> >  inet 192.168.8.168  netmask 255.255.255.0  broadcast 192.168.8.255
> >
> > The inet will be your IP address for your computer.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 08:03:48 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Hi Mick,
> > >
> > > What is the easiest way of finding the IP for the IRLP Computer? I am
> > sure
> > > that's where the issue is at. It lists 13 possible IP addresses.
> > >
> > > Thanks
> > >
> > > Bob N5KF
> > >
> > > On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
>



Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Good news...I "think" i got it...9990 repeated my transmission.  Will run trouble shooting one more time.

Thanks 

Bob N5KF 
Node 3437

On Fri, Jan 10, 2020, 9:39 PM Bob Redoutey N5KF via Groups.Io <redoutey=gmail.com@groups.io> wrote:
The troubleshooting script still gives the same errors. 

Somewhere I am not getting it set right....ugh!

Bob N5KF 

Ps...sorry for all the bandwidth on this issue.

On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Log into your IRLP computer and run the command    ifconfig  Look for this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
 inet 192.168.8.168  netmask 255.255.255.0  broadcast 192.168.8.255

The inet will be your IP address for your computer.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Hi Mick,
>
> What is the easiest way of finding the IP for the IRLP Computer? I am sure
> that's where the issue is at. It lists 13 possible IP addresses.
>
> Thanks
>
> Bob N5KF
>
> On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Just setup your DMZ for your IRLP computer and use it. With the DMZ there
> > won't be any ports to open, they should already be open. From what I can
> > find, your ISP doesn't block any of the ports that matter to IRLP.
> >
> > There would only be one IP address and the ports would be related to that
> > IP address.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:50:52 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Yes, it does have the DMZ option.
> > >
> > > No, I don't have the model #, maybe Altice One.
> > >
> > > Thing that was strange was that the ports were listed under only one IP
> > > address, probably not the IRLP device, but couldn't figure out how to
> > open
> > > up for all IP addresses.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > Sorry, I don't know that router, or all that many routers. I have
> > looked
> > > > some on google. A couple of things that I did find:
> > > >
> > > > "To enable *port forwarding* on your system you will need to make
> > “*port*
> > > > rules” in your router to *allow* select traffic from the internet to
> > > > *allow* access to devices on your network. ..."
> > > >
> > > > "If You Ever Had Their "Smart Router" With Legacy It's Similar
> > Firmware.
> > > > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc.
> > HOWEVER
> > > > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > > > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> > > >
> > > > Do you have a model number for your router?
> > > >
> > > > Also, can you set up your node for DMZ?
> > > >
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 07:08:23 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > Thank you Mick. Yes, I get errors related to DNS not setup
> > correctly.
> > > > >
> > > > > Also TCP Port 15425 not forwarding correctly.
> > > > >
> > > > > UDP Error, all ports not forwarded correctly.
> > > > >
> > > > > Outbound Ports Correct.
> > > > >
> > > > > Everything else passed.
> > > > >
> > > > > So, it sounds like I didn't set up the router correctly...it was
> > > > confusing.
> > > > >
> > > > > It's a Altice (Suddenlink)
> > > > >
> > > > > Familiar with it?
> > > > >
> > > > > Might have to reboot something, as it (the router) won't come up
> > now!
> > > > >
> > > > > Thanks for the trouble shooting so far.
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > >
> > > > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater
> > Association
> > > > > (TARRA) wrote:
> > > > >
> > > > > > That is one of the reasons for the echo reflectors. What do you
> > get
> > > > when
> > > > > > you run troubleshoot-irlp?
> > > > > >
> > > > > > As repeater: troubleshoot-irlp
> > > > > > Mick - W7CAT
> > > > > > Node 3464
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: Bob Redoutey N5KF
> > > > > > To: IRLP@irlp.groups.io
> > > > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > > > >
> > > > > > > I did the easy solution, went with a bridge, but all I could
> > find
> > > > was
> > > > > > "AC
> > > > > > > Line" one. I opened IRLP/Echolink ports on the new router. I
> > seem to
> > > > > > > connect to reflectors, but not getting any replies. The router
> > has
> > > > only
> > > > > > 2
> > > > > > > options, TCP or UDP. No SSH. DMZ is available. When the node
> > boots
> > > > up it
> > > > > > > says connected IRLP and Echolink.
> > > > > > >
> > > > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > > > >
> > > > > > > Bob N5KF
> > > > > > > Node 3437
> > > > > > > Georgetown TX
> > > > > > >
> > > > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > > > >
> > > > > > > > Alternately, you can just add the SSID and Preshared Key info
> > into
> > > > the
> > > > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > > > >
> > > > > > > > allow-hotplug wlan0
> > > > > > > > iface wlan0 inet static
> > > > > > > > address 10.1.1.31
> > > > > > > > netmask 255.255.255.0
> > > > > > > > gateway 10.1.1.1
> > > > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > > > wpa-psk SuperSecretWifiPassword
> > > > > > > >
> > > > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > > > just
> > > > > > plug
> > > > > > > > and play. By default on an IRLP install it will come up as
> > wlan0
> > > > if
> > > > > > > > recognized.
> > > > > > > >
> > > > > > > > Plug it in, then run
> > > > > > > >
> > > > > > > > dmesg
> > > > > > > >
> > > > > > > > and look at the last few lines. Any errors should show up
> > there.
> > > > > > > >
> > > > > > > > Dave Cameron
> > > > > > > >
> > > > > > > >
> > > > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > > > Bob Redoutey N5KF wrote:
> > > > > > > > >> Yes, adding USB WiFi would be easy. My question is...what
> > is
> > > > > > > > >> involved? No, it's not a ancient node. It's the AT style
> > Dave
> > > > > > Cameron
> > > > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > > > automatically
> > > > > > > > >> configure to the new IP address? Or do I need to get into
> > the
> > > > > > > > >> computer setup? I know I need to open ports on the new
> > > > Router/WiFi
> > > > > > > > setup.
> > > > > > > > >
> > > > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find
> > the
> > > > name
> > > > > > of
> > > > > > > > > the new interface (probably wlan0 but maybe something like
> > > > wlp1s0,
> > > > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > > > /etc/network/interfaces somewhat like:
> > > > > > > > >
> > > > > > > > > allow-hotplug wlan0
> > > > > > > > > iface wlan0 inet static
> > > > > > > > > address 10.1.1.31
> > > > > > > > > netmask 255.255.255.0
> > > > > > > > > gateway 10.1.1.1
> > > > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > > > >
> > > > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would
> > include
> > > > > > > > > something like:
> > > > > > > > >
> > > > > > > > > network={
> > > > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > USUALLY Linux would just autoconfigure it using DHCP and
> > stuff,
> > > > but
> > > > > > if
> > > > > > > > > I recall, IRLP install disables this.
> > > > > > > > >
> > > > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of
> > your
> > > > WiFi
> > > > > > > > > network and want to scan.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > Nick VA3NNW
> > > > > > > > >
> > > > > > > > > --
> > > > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > > > use Std::Disclaimer;sig@...
> > > > > > > > > Vitamin C deficiency is apauling
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > --
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

John
 

Have you RE booted both router and irlp, Bob?

John @ 6163

On 11/01/2020 1:39:26 PM, Bob Redoutey N5KF (redoutey@...) wrote:
The troubleshooting script still gives the same errors.
Somewhere I am not getting it set right....ugh!
Bob N5KF
Ps...sorry for all the bandwidth on this issue.
On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association
(TARRA) <tarra@...> wrote:

Log into your IRLP computer and run the command ifconfig Look for this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.8.168 netmask 255.255.255.0 broadcast 192.168.8.255

The inet will be your IP address for your computer.
Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

Hi Mick,

What is the easiest way of finding the IP for the IRLP Computer? I am
sure
that's where the issue is at. It lists 13 possible IP addresses.

Thanks

Bob N5KF

On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
(TARRA) wrote:

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

The troubleshooting script still gives the same errors. 

Somewhere I am not getting it set right....ugh!

Bob N5KF 

Ps...sorry for all the bandwidth on this issue.

On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Log into your IRLP computer and run the command    ifconfig  Look for this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
 inet 192.168.8.168  netmask 255.255.255.0  broadcast 192.168.8.255

The inet will be your IP address for your computer.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Hi Mick,
>
> What is the easiest way of finding the IP for the IRLP Computer? I am sure
> that's where the issue is at. It lists 13 possible IP addresses.
>
> Thanks
>
> Bob N5KF
>
> On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Just setup your DMZ for your IRLP computer and use it. With the DMZ there
> > won't be any ports to open, they should already be open. From what I can
> > find, your ISP doesn't block any of the ports that matter to IRLP.
> >
> > There would only be one IP address and the ports would be related to that
> > IP address.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:50:52 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Yes, it does have the DMZ option.
> > >
> > > No, I don't have the model #, maybe Altice One.
> > >
> > > Thing that was strange was that the ports were listed under only one IP
> > > address, probably not the IRLP device, but couldn't figure out how to
> > open
> > > up for all IP addresses.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > Sorry, I don't know that router, or all that many routers. I have
> > looked
> > > > some on google. A couple of things that I did find:
> > > >
> > > > "To enable *port forwarding* on your system you will need to make
> > “*port*
> > > > rules” in your router to *allow* select traffic from the internet to
> > > > *allow* access to devices on your network. ..."
> > > >
> > > > "If You Ever Had Their "Smart Router" With Legacy It's Similar
> > Firmware.
> > > > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc.
> > HOWEVER
> > > > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > > > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> > > >
> > > > Do you have a model number for your router?
> > > >
> > > > Also, can you set up your node for DMZ?
> > > >
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 07:08:23 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > Thank you Mick. Yes, I get errors related to DNS not setup
> > correctly.
> > > > >
> > > > > Also TCP Port 15425 not forwarding correctly.
> > > > >
> > > > > UDP Error, all ports not forwarded correctly.
> > > > >
> > > > > Outbound Ports Correct.
> > > > >
> > > > > Everything else passed.
> > > > >
> > > > > So, it sounds like I didn't set up the router correctly...it was
> > > > confusing.
> > > > >
> > > > > It's a Altice (Suddenlink)
> > > > >
> > > > > Familiar with it?
> > > > >
> > > > > Might have to reboot something, as it (the router) won't come up
> > now!
> > > > >
> > > > > Thanks for the trouble shooting so far.
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > >
> > > > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater
> > Association
> > > > > (TARRA) wrote:
> > > > >
> > > > > > That is one of the reasons for the echo reflectors. What do you
> > get
> > > > when
> > > > > > you run troubleshoot-irlp?
> > > > > >
> > > > > > As repeater: troubleshoot-irlp
> > > > > > Mick - W7CAT
> > > > > > Node 3464
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: Bob Redoutey N5KF
> > > > > > To: IRLP@irlp.groups.io
> > > > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > > > >
> > > > > > > I did the easy solution, went with a bridge, but all I could
> > find
> > > > was
> > > > > > "AC
> > > > > > > Line" one. I opened IRLP/Echolink ports on the new router. I
> > seem to
> > > > > > > connect to reflectors, but not getting any replies. The router
> > has
> > > > only
> > > > > > 2
> > > > > > > options, TCP or UDP. No SSH. DMZ is available. When the node
> > boots
> > > > up it
> > > > > > > says connected IRLP and Echolink.
> > > > > > >
> > > > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > > > >
> > > > > > > Bob N5KF
> > > > > > > Node 3437
> > > > > > > Georgetown TX
> > > > > > >
> > > > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > > > >
> > > > > > > > Alternately, you can just add the SSID and Preshared Key info
> > into
> > > > the
> > > > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > > > >
> > > > > > > > allow-hotplug wlan0
> > > > > > > > iface wlan0 inet static
> > > > > > > > address 10.1.1.31
> > > > > > > > netmask 255.255.255.0
> > > > > > > > gateway 10.1.1.1
> > > > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > > > wpa-psk SuperSecretWifiPassword
> > > > > > > >
> > > > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > > > just
> > > > > > plug
> > > > > > > > and play. By default on an IRLP install it will come up as
> > wlan0
> > > > if
> > > > > > > > recognized.
> > > > > > > >
> > > > > > > > Plug it in, then run
> > > > > > > >
> > > > > > > > dmesg
> > > > > > > >
> > > > > > > > and look at the last few lines. Any errors should show up
> > there.
> > > > > > > >
> > > > > > > > Dave Cameron
> > > > > > > >
> > > > > > > >
> > > > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > > > Bob Redoutey N5KF wrote:
> > > > > > > > >> Yes, adding USB WiFi would be easy. My question is...what
> > is
> > > > > > > > >> involved? No, it's not a ancient node. It's the AT style
> > Dave
> > > > > > Cameron
> > > > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > > > automatically
> > > > > > > > >> configure to the new IP address? Or do I need to get into
> > the
> > > > > > > > >> computer setup? I know I need to open ports on the new
> > > > Router/WiFi
> > > > > > > > setup.
> > > > > > > > >
> > > > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find
> > the
> > > > name
> > > > > > of
> > > > > > > > > the new interface (probably wlan0 but maybe something like
> > > > wlp1s0,
> > > > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > > > /etc/network/interfaces somewhat like:
> > > > > > > > >
> > > > > > > > > allow-hotplug wlan0
> > > > > > > > > iface wlan0 inet static
> > > > > > > > > address 10.1.1.31
> > > > > > > > > netmask 255.255.255.0
> > > > > > > > > gateway 10.1.1.1
> > > > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > > > >
> > > > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would
> > include
> > > > > > > > > something like:
> > > > > > > > >
> > > > > > > > > network={
> > > > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > USUALLY Linux would just autoconfigure it using DHCP and
> > stuff,
> > > > but
> > > > > > if
> > > > > > > > > I recall, IRLP install disables this.
> > > > > > > > >
> > > > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of
> > your
> > > > WiFi
> > > > > > > > > network and want to scan.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > Nick VA3NNW
> > > > > > > > >
> > > > > > > > > --
> > > > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > > > use Std::Disclaimer;sig@...
> > > > > > > > > Vitamin C deficiency is apauling
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > --
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Hi Mick,

Well...I found it, put it in for the DMZ option...saved it, but still no luck.

I will run the troubleshooting script again.

Thanks for your help

Bob N5KF 

On Fri, Jan 10, 2020, 9:16 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Log into your IRLP computer and run the command    ifconfig  Look for this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
 inet 192.168.8.168  netmask 255.255.255.0  broadcast 192.168.8.255

The inet will be your IP address for your computer.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Hi Mick,
>
> What is the easiest way of finding the IP for the IRLP Computer? I am sure
> that's where the issue is at. It lists 13 possible IP addresses.
>
> Thanks
>
> Bob N5KF
>
> On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Just setup your DMZ for your IRLP computer and use it. With the DMZ there
> > won't be any ports to open, they should already be open. From what I can
> > find, your ISP doesn't block any of the ports that matter to IRLP.
> >
> > There would only be one IP address and the ports would be related to that
> > IP address.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:50:52 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Yes, it does have the DMZ option.
> > >
> > > No, I don't have the model #, maybe Altice One.
> > >
> > > Thing that was strange was that the ports were listed under only one IP
> > > address, probably not the IRLP device, but couldn't figure out how to
> > open
> > > up for all IP addresses.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > Sorry, I don't know that router, or all that many routers. I have
> > looked
> > > > some on google. A couple of things that I did find:
> > > >
> > > > "To enable *port forwarding* on your system you will need to make
> > “*port*
> > > > rules” in your router to *allow* select traffic from the internet to
> > > > *allow* access to devices on your network. ..."
> > > >
> > > > "If You Ever Had Their "Smart Router" With Legacy It's Similar
> > Firmware.
> > > > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc.
> > HOWEVER
> > > > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > > > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> > > >
> > > > Do you have a model number for your router?
> > > >
> > > > Also, can you set up your node for DMZ?
> > > >
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 07:08:23 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > Thank you Mick. Yes, I get errors related to DNS not setup
> > correctly.
> > > > >
> > > > > Also TCP Port 15425 not forwarding correctly.
> > > > >
> > > > > UDP Error, all ports not forwarded correctly.
> > > > >
> > > > > Outbound Ports Correct.
> > > > >
> > > > > Everything else passed.
> > > > >
> > > > > So, it sounds like I didn't set up the router correctly...it was
> > > > confusing.
> > > > >
> > > > > It's a Altice (Suddenlink)
> > > > >
> > > > > Familiar with it?
> > > > >
> > > > > Might have to reboot something, as it (the router) won't come up
> > now!
> > > > >
> > > > > Thanks for the trouble shooting so far.
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > >
> > > > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater
> > Association
> > > > > (TARRA) wrote:
> > > > >
> > > > > > That is one of the reasons for the echo reflectors. What do you
> > get
> > > > when
> > > > > > you run troubleshoot-irlp?
> > > > > >
> > > > > > As repeater: troubleshoot-irlp
> > > > > > Mick - W7CAT
> > > > > > Node 3464
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: Bob Redoutey N5KF
> > > > > > To: IRLP@irlp.groups.io
> > > > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > > > >
> > > > > > > I did the easy solution, went with a bridge, but all I could
> > find
> > > > was
> > > > > > "AC
> > > > > > > Line" one. I opened IRLP/Echolink ports on the new router. I
> > seem to
> > > > > > > connect to reflectors, but not getting any replies. The router
> > has
> > > > only
> > > > > > 2
> > > > > > > options, TCP or UDP. No SSH. DMZ is available. When the node
> > boots
> > > > up it
> > > > > > > says connected IRLP and Echolink.
> > > > > > >
> > > > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > > > >
> > > > > > > Bob N5KF
> > > > > > > Node 3437
> > > > > > > Georgetown TX
> > > > > > >
> > > > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > > > >
> > > > > > > > Alternately, you can just add the SSID and Preshared Key info
> > into
> > > > the
> > > > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > > > >
> > > > > > > > allow-hotplug wlan0
> > > > > > > > iface wlan0 inet static
> > > > > > > > address 10.1.1.31
> > > > > > > > netmask 255.255.255.0
> > > > > > > > gateway 10.1.1.1
> > > > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > > > wpa-psk SuperSecretWifiPassword
> > > > > > > >
> > > > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > > > just
> > > > > > plug
> > > > > > > > and play. By default on an IRLP install it will come up as
> > wlan0
> > > > if
> > > > > > > > recognized.
> > > > > > > >
> > > > > > > > Plug it in, then run
> > > > > > > >
> > > > > > > > dmesg
> > > > > > > >
> > > > > > > > and look at the last few lines. Any errors should show up
> > there.
> > > > > > > >
> > > > > > > > Dave Cameron
> > > > > > > >
> > > > > > > >
> > > > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > > > Bob Redoutey N5KF wrote:
> > > > > > > > >> Yes, adding USB WiFi would be easy. My question is...what
> > is
> > > > > > > > >> involved? No, it's not a ancient node. It's the AT style
> > Dave
> > > > > > Cameron
> > > > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > > > automatically
> > > > > > > > >> configure to the new IP address? Or do I need to get into
> > the
> > > > > > > > >> computer setup? I know I need to open ports on the new
> > > > Router/WiFi
> > > > > > > > setup.
> > > > > > > > >
> > > > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find
> > the
> > > > name
> > > > > > of
> > > > > > > > > the new interface (probably wlan0 but maybe something like
> > > > wlp1s0,
> > > > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > > > /etc/network/interfaces somewhat like:
> > > > > > > > >
> > > > > > > > > allow-hotplug wlan0
> > > > > > > > > iface wlan0 inet static
> > > > > > > > > address 10.1.1.31
> > > > > > > > > netmask 255.255.255.0
> > > > > > > > > gateway 10.1.1.1
> > > > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > > > >
> > > > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would
> > include
> > > > > > > > > something like:
> > > > > > > > >
> > > > > > > > > network={
> > > > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > USUALLY Linux would just autoconfigure it using DHCP and
> > stuff,
> > > > but
> > > > > > if
> > > > > > > > > I recall, IRLP install disables this.
> > > > > > > > >
> > > > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of
> > your
> > > > WiFi
> > > > > > > > > network and want to scan.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > Nick VA3NNW
> > > > > > > > >
> > > > > > > > > --
> > > > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > > > use Std::Disclaimer;sig@...
> > > > > > > > > Vitamin C deficiency is apauling
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > --
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

Log into your IRLP computer and run the command    ifconfig  Look for this:

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
 inet 192.168.8.168  netmask 255.255.255.0  broadcast 192.168.8.255

The inet will be your IP address for your computer.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Hi Mick,
>
> What is the easiest way of finding the IP for the IRLP Computer? I am sure
> that's where the issue is at. It lists 13 possible IP addresses.
>
> Thanks
>
> Bob N5KF
>
> On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Just setup your DMZ for your IRLP computer and use it. With the DMZ there
> > won't be any ports to open, they should already be open. From what I can
> > find, your ISP doesn't block any of the ports that matter to IRLP.
> >
> > There would only be one IP address and the ports would be related to that
> > IP address.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:50:52 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Yes, it does have the DMZ option.
> > >
> > > No, I don't have the model #, maybe Altice One.
> > >
> > > Thing that was strange was that the ports were listed under only one IP
> > > address, probably not the IRLP device, but couldn't figure out how to
> > open
> > > up for all IP addresses.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > Sorry, I don't know that router, or all that many routers. I have
> > looked
> > > > some on google. A couple of things that I did find:
> > > >
> > > > "To enable *port forwarding* on your system you will need to make
> > “*port*
> > > > rules” in your router to *allow* select traffic from the internet to
> > > > *allow* access to devices on your network. ..."
> > > >
> > > > "If You Ever Had Their "Smart Router" With Legacy It's Similar
> > Firmware.
> > > > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc.
> > HOWEVER
> > > > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > > > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> > > >
> > > > Do you have a model number for your router?
> > > >
> > > > Also, can you set up your node for DMZ?
> > > >
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 07:08:23 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > Thank you Mick. Yes, I get errors related to DNS not setup
> > correctly.
> > > > >
> > > > > Also TCP Port 15425 not forwarding correctly.
> > > > >
> > > > > UDP Error, all ports not forwarded correctly.
> > > > >
> > > > > Outbound Ports Correct.
> > > > >
> > > > > Everything else passed.
> > > > >
> > > > > So, it sounds like I didn't set up the router correctly...it was
> > > > confusing.
> > > > >
> > > > > It's a Altice (Suddenlink)
> > > > >
> > > > > Familiar with it?
> > > > >
> > > > > Might have to reboot something, as it (the router) won't come up
> > now!
> > > > >
> > > > > Thanks for the trouble shooting so far.
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > >
> > > > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater
> > Association
> > > > > (TARRA) wrote:
> > > > >
> > > > > > That is one of the reasons for the echo reflectors. What do you
> > get
> > > > when
> > > > > > you run troubleshoot-irlp?
> > > > > >
> > > > > > As repeater: troubleshoot-irlp
> > > > > > Mick - W7CAT
> > > > > > Node 3464
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: Bob Redoutey N5KF
> > > > > > To: IRLP@irlp.groups.io
> > > > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > > > >
> > > > > > > I did the easy solution, went with a bridge, but all I could
> > find
> > > > was
> > > > > > "AC
> > > > > > > Line" one. I opened IRLP/Echolink ports on the new router. I
> > seem to
> > > > > > > connect to reflectors, but not getting any replies. The router
> > has
> > > > only
> > > > > > 2
> > > > > > > options, TCP or UDP. No SSH. DMZ is available. When the node
> > boots
> > > > up it
> > > > > > > says connected IRLP and Echolink.
> > > > > > >
> > > > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > > > >
> > > > > > > Bob N5KF
> > > > > > > Node 3437
> > > > > > > Georgetown TX
> > > > > > >
> > > > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > > > >
> > > > > > > > Alternately, you can just add the SSID and Preshared Key info
> > into
> > > > the
> > > > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > > > >
> > > > > > > > allow-hotplug wlan0
> > > > > > > > iface wlan0 inet static
> > > > > > > > address 10.1.1.31
> > > > > > > > netmask 255.255.255.0
> > > > > > > > gateway 10.1.1.1
> > > > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > > > wpa-psk SuperSecretWifiPassword
> > > > > > > >
> > > > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > > > just
> > > > > > plug
> > > > > > > > and play. By default on an IRLP install it will come up as
> > wlan0
> > > > if
> > > > > > > > recognized.
> > > > > > > >
> > > > > > > > Plug it in, then run
> > > > > > > >
> > > > > > > > dmesg
> > > > > > > >
> > > > > > > > and look at the last few lines. Any errors should show up
> > there.
> > > > > > > >
> > > > > > > > Dave Cameron
> > > > > > > >
> > > > > > > >
> > > > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > > > Bob Redoutey N5KF wrote:
> > > > > > > > >> Yes, adding USB WiFi would be easy. My question is...what
> > is
> > > > > > > > >> involved? No, it's not a ancient node. It's the AT style
> > Dave
> > > > > > Cameron
> > > > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > > > automatically
> > > > > > > > >> configure to the new IP address? Or do I need to get into
> > the
> > > > > > > > >> computer setup? I know I need to open ports on the new
> > > > Router/WiFi
> > > > > > > > setup.
> > > > > > > > >
> > > > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find
> > the
> > > > name
> > > > > > of
> > > > > > > > > the new interface (probably wlan0 but maybe something like
> > > > wlp1s0,
> > > > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > > > /etc/network/interfaces somewhat like:
> > > > > > > > >
> > > > > > > > > allow-hotplug wlan0
> > > > > > > > > iface wlan0 inet static
> > > > > > > > > address 10.1.1.31
> > > > > > > > > netmask 255.255.255.0
> > > > > > > > > gateway 10.1.1.1
> > > > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > > > >
> > > > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would
> > include
> > > > > > > > > something like:
> > > > > > > > >
> > > > > > > > > network={
> > > > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > USUALLY Linux would just autoconfigure it using DHCP and
> > stuff,
> > > > but
> > > > > > if
> > > > > > > > > I recall, IRLP install disables this.
> > > > > > > > >
> > > > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of
> > your
> > > > WiFi
> > > > > > > > > network and want to scan.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > Nick VA3NNW
> > > > > > > > >
> > > > > > > > > --
> > > > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > > > use Std::Disclaimer;sig@...
> > > > > > > > > Vitamin C deficiency is apauling
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > --
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

Log into your IRLP computer and run the command    ifconfig

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 08:03:48 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Hi Mick,
>
> What is the easiest way of finding the IP for the IRLP Computer? I am sure
> that's where the issue is at. It lists 13 possible IP addresses.
>
> Thanks
>
> Bob N5KF
>
> On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Just setup your DMZ for your IRLP computer and use it. With the DMZ there
> > won't be any ports to open, they should already be open. From what I can
> > find, your ISP doesn't block any of the ports that matter to IRLP.
> >
> > There would only be one IP address and the ports would be related to that
> > IP address.
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:50:52 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Yes, it does have the DMZ option.
> > >
> > > No, I don't have the model #, maybe Altice One.
> > >
> > > Thing that was strange was that the ports were listed under only one IP
> > > address, probably not the IRLP device, but couldn't figure out how to
> > open
> > > up for all IP addresses.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > Sorry, I don't know that router, or all that many routers. I have
> > looked
> > > > some on google. A couple of things that I did find:
> > > >
> > > > "To enable *port forwarding* on your system you will need to make
> > “*port*
> > > > rules” in your router to *allow* select traffic from the internet to
> > > > *allow* access to devices on your network. ..."
> > > >
> > > > "If You Ever Had Their "Smart Router" With Legacy It's Similar
> > Firmware.
> > > > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc.
> > HOWEVER
> > > > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > > > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> > > >
> > > > Do you have a model number for your router?
> > > >
> > > > Also, can you set up your node for DMZ?
> > > >
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 07:08:23 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > Thank you Mick. Yes, I get errors related to DNS not setup
> > correctly.
> > > > >
> > > > > Also TCP Port 15425 not forwarding correctly.
> > > > >
> > > > > UDP Error, all ports not forwarded correctly.
> > > > >
> > > > > Outbound Ports Correct.
> > > > >
> > > > > Everything else passed.
> > > > >
> > > > > So, it sounds like I didn't set up the router correctly...it was
> > > > confusing.
> > > > >
> > > > > It's a Altice (Suddenlink)
> > > > >
> > > > > Familiar with it?
> > > > >
> > > > > Might have to reboot something, as it (the router) won't come up
> > now!
> > > > >
> > > > > Thanks for the trouble shooting so far.
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > >
> > > > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater
> > Association
> > > > > (TARRA) wrote:
> > > > >
> > > > > > That is one of the reasons for the echo reflectors. What do you
> > get
> > > > when
> > > > > > you run troubleshoot-irlp?
> > > > > >
> > > > > > As repeater: troubleshoot-irlp
> > > > > > Mick - W7CAT
> > > > > > Node 3464
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: Bob Redoutey N5KF
> > > > > > To: IRLP@irlp.groups.io
> > > > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > > > >
> > > > > > > I did the easy solution, went with a bridge, but all I could
> > find
> > > > was
> > > > > > "AC
> > > > > > > Line" one. I opened IRLP/Echolink ports on the new router. I
> > seem to
> > > > > > > connect to reflectors, but not getting any replies. The router
> > has
> > > > only
> > > > > > 2
> > > > > > > options, TCP or UDP. No SSH. DMZ is available. When the node
> > boots
> > > > up it
> > > > > > > says connected IRLP and Echolink.
> > > > > > >
> > > > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > > > >
> > > > > > > Bob N5KF
> > > > > > > Node 3437
> > > > > > > Georgetown TX
> > > > > > >
> > > > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > > > >
> > > > > > > > Alternately, you can just add the SSID and Preshared Key info
> > into
> > > > the
> > > > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > > > >
> > > > > > > > allow-hotplug wlan0
> > > > > > > > iface wlan0 inet static
> > > > > > > > address 10.1.1.31
> > > > > > > > netmask 255.255.255.0
> > > > > > > > gateway 10.1.1.1
> > > > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > > > wpa-psk SuperSecretWifiPassword
> > > > > > > >
> > > > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > > > just
> > > > > > plug
> > > > > > > > and play. By default on an IRLP install it will come up as
> > wlan0
> > > > if
> > > > > > > > recognized.
> > > > > > > >
> > > > > > > > Plug it in, then run
> > > > > > > >
> > > > > > > > dmesg
> > > > > > > >
> > > > > > > > and look at the last few lines. Any errors should show up
> > there.
> > > > > > > >
> > > > > > > > Dave Cameron
> > > > > > > >
> > > > > > > >
> > > > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > > > Bob Redoutey N5KF wrote:
> > > > > > > > >> Yes, adding USB WiFi would be easy. My question is...what
> > is
> > > > > > > > >> involved? No, it's not a ancient node. It's the AT style
> > Dave
> > > > > > Cameron
> > > > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > > > automatically
> > > > > > > > >> configure to the new IP address? Or do I need to get into
> > the
> > > > > > > > >> computer setup? I know I need to open ports on the new
> > > > Router/WiFi
> > > > > > > > setup.
> > > > > > > > >
> > > > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find
> > the
> > > > name
> > > > > > of
> > > > > > > > > the new interface (probably wlan0 but maybe something like
> > > > wlp1s0,
> > > > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > > > /etc/network/interfaces somewhat like:
> > > > > > > > >
> > > > > > > > > allow-hotplug wlan0
> > > > > > > > > iface wlan0 inet static
> > > > > > > > > address 10.1.1.31
> > > > > > > > > netmask 255.255.255.0
> > > > > > > > > gateway 10.1.1.1
> > > > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > > > >
> > > > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would
> > include
> > > > > > > > > something like:
> > > > > > > > >
> > > > > > > > > network={
> > > > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > USUALLY Linux would just autoconfigure it using DHCP and
> > stuff,
> > > > but
> > > > > > if
> > > > > > > > > I recall, IRLP install disables this.
> > > > > > > > >
> > > > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of
> > your
> > > > WiFi
> > > > > > > > > network and want to scan.
> > > > > > > > >
> > > > > > > > >
> > > > > > > > > Nick VA3NNW
> > > > > > > > >
> > > > > > > > > --
> > > > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > > > use Std::Disclaimer;sig@...
> > > > > > > > > Vitamin C deficiency is apauling
> > > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > --
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

It's a all in one box. TV, WiFi and Ethernet ports, all in the same box.

Bob N5KF 

On Fri, Jan 10, 2020, 9:00 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

It looks to me like the Altice One is just a cable modem and not your router. I would expect that you are using a router connected to the Altice.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:50:52 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Yes, it does have the DMZ option.
>
> No, I don't have the model #, maybe Altice One.
>
> Thing that was strange was that the ports were listed under only one IP
> address, probably not the IRLP device, but couldn't figure out how to open
> up for all IP addresses.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Sorry, I don't know that router, or all that many routers. I have looked
> > some on google. A couple of things that I did find:
> >
> > "To enable *port forwarding* on your system you will need to make “*port*
> > rules” in your router to *allow* select traffic from the internet to
> > *allow* access to devices on your network. ..."
> >
> > "If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware.
> > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER
> > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> >
> > Do you have a model number for your router?
> >
> > Also, can you set up your node for DMZ?
> >
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:08:23 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Thank you Mick. Yes, I get errors related to DNS not setup correctly.
> > >
> > > Also TCP Port 15425 not forwarding correctly.
> > >
> > > UDP Error, all ports not forwarded correctly.
> > >
> > > Outbound Ports Correct.
> > >
> > > Everything else passed.
> > >
> > > So, it sounds like I didn't set up the router correctly...it was
> > confusing.
> > >
> > > It's a Altice (Suddenlink)
> > >
> > > Familiar with it?
> > >
> > > Might have to reboot something, as it (the router) won't come up now!
> > >
> > > Thanks for the trouble shooting so far.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > That is one of the reasons for the echo reflectors. What do you get
> > when
> > > > you run troubleshoot-irlp?
> > > >
> > > > As repeater: troubleshoot-irlp
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > I did the easy solution, went with a bridge, but all I could find
> > was
> > > > "AC
> > > > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > > > connect to reflectors, but not getting any replies. The router has
> > only
> > > > 2
> > > > > options, TCP or UDP. No SSH. DMZ is available. When the node boots
> > up it
> > > > > says connected IRLP and Echolink.
> > > > >
> > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > > Georgetown TX
> > > > >
> > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > >
> > > > > > Alternately, you can just add the SSID and Preshared Key info into
> > the
> > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > >
> > > > > > allow-hotplug wlan0
> > > > > > iface wlan0 inet static
> > > > > > address 10.1.1.31
> > > > > > netmask 255.255.255.0
> > > > > > gateway 10.1.1.1
> > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > wpa-psk SuperSecretWifiPassword
> > > > > >
> > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > just
> > > > plug
> > > > > > and play. By default on an IRLP install it will come up as wlan0
> > if
> > > > > > recognized.
> > > > > >
> > > > > > Plug it in, then run
> > > > > >
> > > > > > dmesg
> > > > > >
> > > > > > and look at the last few lines. Any errors should show up there.
> > > > > >
> > > > > > Dave Cameron
> > > > > >
> > > > > >
> > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > Bob Redoutey N5KF wrote:
> > > > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > > > Cameron
> > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > automatically
> > > > > > >> configure to the new IP address? Or do I need to get into the
> > > > > > >> computer setup? I know I need to open ports on the new
> > Router/WiFi
> > > > > > setup.
> > > > > > >
> > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the
> > name
> > > > of
> > > > > > > the new interface (probably wlan0 but maybe something like
> > wlp1s0,
> > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > /etc/network/interfaces somewhat like:
> > > > > > >
> > > > > > > allow-hotplug wlan0
> > > > > > > iface wlan0 inet static
> > > > > > > address 10.1.1.31
> > > > > > > netmask 255.255.255.0
> > > > > > > gateway 10.1.1.1
> > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > >
> > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > > > something like:
> > > > > > >
> > > > > > > network={
> > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > }
> > > > > > >
> > > > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff,
> > but
> > > > if
> > > > > > > I recall, IRLP install disables this.
> > > > > > >
> > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your
> > WiFi
> > > > > > > network and want to scan.
> > > > > > >
> > > > > > >
> > > > > > > Nick VA3NNW
> > > > > > >
> > > > > > > --
> > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > use Std::Disclaimer;sig@...
> > > > > > > Vitamin C deficiency is apauling
> > > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Hi Mick,

What is the easiest way of finding the IP for the IRLP Computer? I am sure that's where the issue is at. It lists 13 possible IP addresses.

Thanks 

Bob N5KF 

On Fri, Jan 10, 2020, 8:56 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Just setup your DMZ for your IRLP computer and use it. With the DMZ there won't be any ports to open, they should already be open. From what I can find, your ISP doesn't block any of the ports that matter to IRLP.

There would only be one IP address and the ports would be related to that IP address.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:50:52 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Yes, it does have the DMZ option.
>
> No, I don't have the model #, maybe Altice One.
>
> Thing that was strange was that the ports were listed under only one IP
> address, probably not the IRLP device, but couldn't figure out how to open
> up for all IP addresses.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Sorry, I don't know that router, or all that many routers. I have looked
> > some on google. A couple of things that I did find:
> >
> > "To enable *port forwarding* on your system you will need to make “*port*
> > rules” in your router to *allow* select traffic from the internet to
> > *allow* access to devices on your network. ..."
> >
> > "If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware.
> > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER
> > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> >
> > Do you have a model number for your router?
> >
> > Also, can you set up your node for DMZ?
> >
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:08:23 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Thank you Mick. Yes, I get errors related to DNS not setup correctly.
> > >
> > > Also TCP Port 15425 not forwarding correctly.
> > >
> > > UDP Error, all ports not forwarded correctly.
> > >
> > > Outbound Ports Correct.
> > >
> > > Everything else passed.
> > >
> > > So, it sounds like I didn't set up the router correctly...it was
> > confusing.
> > >
> > > It's a Altice (Suddenlink)
> > >
> > > Familiar with it?
> > >
> > > Might have to reboot something, as it (the router) won't come up now!
> > >
> > > Thanks for the trouble shooting so far.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > That is one of the reasons for the echo reflectors. What do you get
> > when
> > > > you run troubleshoot-irlp?
> > > >
> > > > As repeater: troubleshoot-irlp
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > I did the easy solution, went with a bridge, but all I could find
> > was
> > > > "AC
> > > > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > > > connect to reflectors, but not getting any replies. The router has
> > only
> > > > 2
> > > > > options, TCP or UDP. No SSH. DMZ is available. When the node boots
> > up it
> > > > > says connected IRLP and Echolink.
> > > > >
> > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > > Georgetown TX
> > > > >
> > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > >
> > > > > > Alternately, you can just add the SSID and Preshared Key info into
> > the
> > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > >
> > > > > > allow-hotplug wlan0
> > > > > > iface wlan0 inet static
> > > > > > address 10.1.1.31
> > > > > > netmask 255.255.255.0
> > > > > > gateway 10.1.1.1
> > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > wpa-psk SuperSecretWifiPassword
> > > > > >
> > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > just
> > > > plug
> > > > > > and play. By default on an IRLP install it will come up as wlan0
> > if
> > > > > > recognized.
> > > > > >
> > > > > > Plug it in, then run
> > > > > >
> > > > > > dmesg
> > > > > >
> > > > > > and look at the last few lines. Any errors should show up there.
> > > > > >
> > > > > > Dave Cameron
> > > > > >
> > > > > >
> > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > Bob Redoutey N5KF wrote:
> > > > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > > > Cameron
> > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > automatically
> > > > > > >> configure to the new IP address? Or do I need to get into the
> > > > > > >> computer setup? I know I need to open ports on the new
> > Router/WiFi
> > > > > > setup.
> > > > > > >
> > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the
> > name
> > > > of
> > > > > > > the new interface (probably wlan0 but maybe something like
> > wlp1s0,
> > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > /etc/network/interfaces somewhat like:
> > > > > > >
> > > > > > > allow-hotplug wlan0
> > > > > > > iface wlan0 inet static
> > > > > > > address 10.1.1.31
> > > > > > > netmask 255.255.255.0
> > > > > > > gateway 10.1.1.1
> > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > >
> > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > > > something like:
> > > > > > >
> > > > > > > network={
> > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > }
> > > > > > >
> > > > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff,
> > but
> > > > if
> > > > > > > I recall, IRLP install disables this.
> > > > > > >
> > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your
> > WiFi
> > > > > > > network and want to scan.
> > > > > > >
> > > > > > >
> > > > > > > Nick VA3NNW
> > > > > > >
> > > > > > > --
> > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > use Std::Disclaimer;sig@...
> > > > > > > Vitamin C deficiency is apauling
> > > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

It looks to me like the Altice One is just a cable modem and not your router. I would expect that you are using a router connected to the Altice.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:50:52 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Yes, it does have the DMZ option.
>
> No, I don't have the model #, maybe Altice One.
>
> Thing that was strange was that the ports were listed under only one IP
> address, probably not the IRLP device, but couldn't figure out how to open
> up for all IP addresses.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Sorry, I don't know that router, or all that many routers. I have looked
> > some on google. A couple of things that I did find:
> >
> > "To enable *port forwarding* on your system you will need to make “*port*
> > rules” in your router to *allow* select traffic from the internet to
> > *allow* access to devices on your network. ..."
> >
> > "If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware.
> > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER
> > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> >
> > Do you have a model number for your router?
> >
> > Also, can you set up your node for DMZ?
> >
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:08:23 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Thank you Mick. Yes, I get errors related to DNS not setup correctly.
> > >
> > > Also TCP Port 15425 not forwarding correctly.
> > >
> > > UDP Error, all ports not forwarded correctly.
> > >
> > > Outbound Ports Correct.
> > >
> > > Everything else passed.
> > >
> > > So, it sounds like I didn't set up the router correctly...it was
> > confusing.
> > >
> > > It's a Altice (Suddenlink)
> > >
> > > Familiar with it?
> > >
> > > Might have to reboot something, as it (the router) won't come up now!
> > >
> > > Thanks for the trouble shooting so far.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > That is one of the reasons for the echo reflectors. What do you get
> > when
> > > > you run troubleshoot-irlp?
> > > >
> > > > As repeater: troubleshoot-irlp
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > I did the easy solution, went with a bridge, but all I could find
> > was
> > > > "AC
> > > > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > > > connect to reflectors, but not getting any replies. The router has
> > only
> > > > 2
> > > > > options, TCP or UDP. No SSH. DMZ is available. When the node boots
> > up it
> > > > > says connected IRLP and Echolink.
> > > > >
> > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > > Georgetown TX
> > > > >
> > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > >
> > > > > > Alternately, you can just add the SSID and Preshared Key info into
> > the
> > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > >
> > > > > > allow-hotplug wlan0
> > > > > > iface wlan0 inet static
> > > > > > address 10.1.1.31
> > > > > > netmask 255.255.255.0
> > > > > > gateway 10.1.1.1
> > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > wpa-psk SuperSecretWifiPassword
> > > > > >
> > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > just
> > > > plug
> > > > > > and play. By default on an IRLP install it will come up as wlan0
> > if
> > > > > > recognized.
> > > > > >
> > > > > > Plug it in, then run
> > > > > >
> > > > > > dmesg
> > > > > >
> > > > > > and look at the last few lines. Any errors should show up there.
> > > > > >
> > > > > > Dave Cameron
> > > > > >
> > > > > >
> > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > Bob Redoutey N5KF wrote:
> > > > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > > > Cameron
> > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > automatically
> > > > > > >> configure to the new IP address? Or do I need to get into the
> > > > > > >> computer setup? I know I need to open ports on the new
> > Router/WiFi
> > > > > > setup.
> > > > > > >
> > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the
> > name
> > > > of
> > > > > > > the new interface (probably wlan0 but maybe something like
> > wlp1s0,
> > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > /etc/network/interfaces somewhat like:
> > > > > > >
> > > > > > > allow-hotplug wlan0
> > > > > > > iface wlan0 inet static
> > > > > > > address 10.1.1.31
> > > > > > > netmask 255.255.255.0
> > > > > > > gateway 10.1.1.1
> > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > >
> > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > > > something like:
> > > > > > >
> > > > > > > network={
> > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > }
> > > > > > >
> > > > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff,
> > but
> > > > if
> > > > > > > I recall, IRLP install disables this.
> > > > > > >
> > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your
> > WiFi
> > > > > > > network and want to scan.
> > > > > > >
> > > > > > >
> > > > > > > Nick VA3NNW
> > > > > > >
> > > > > > > --
> > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > use Std::Disclaimer;sig@...
> > > > > > > Vitamin C deficiency is apauling
> > > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

Just setup your DMZ for your IRLP computer and use it. With the DMZ there won't be any ports to open, they should already be open. From what I can find, your ISP doesn't block any of the ports that matter to IRLP.

There would only be one IP address and the ports would be related to that IP address.

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:50:52 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Yes, it does have the DMZ option.
>
> No, I don't have the model #, maybe Altice One.
>
> Thing that was strange was that the ports were listed under only one IP
> address, probably not the IRLP device, but couldn't figure out how to open
> up for all IP addresses.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > Sorry, I don't know that router, or all that many routers. I have looked
> > some on google. A couple of things that I did find:
> >
> > "To enable *port forwarding* on your system you will need to make “*port*
> > rules” in your router to *allow* select traffic from the internet to
> > *allow* access to devices on your network. ..."
> >
> > "If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware.
> > Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER
> > It's Very Limited. If You Want Full Control Over Network AlticeOne is
> > *NOT*: For YOU! Get Legacy Instead Where Can Use Own Router!"
> >
> > Do you have a model number for your router?
> >
> > Also, can you set up your node for DMZ?
> >
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 07:08:23 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > Thank you Mick. Yes, I get errors related to DNS not setup correctly.
> > >
> > > Also TCP Port 15425 not forwarding correctly.
> > >
> > > UDP Error, all ports not forwarded correctly.
> > >
> > > Outbound Ports Correct.
> > >
> > > Everything else passed.
> > >
> > > So, it sounds like I didn't set up the router correctly...it was
> > confusing.
> > >
> > > It's a Altice (Suddenlink)
> > >
> > > Familiar with it?
> > >
> > > Might have to reboot something, as it (the router) won't come up now!
> > >
> > > Thanks for the trouble shooting so far.
> > >
> > > Bob N5KF
> > > Node 3437
> > >
> > > On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> > > (TARRA) wrote:
> > >
> > > > That is one of the reasons for the echo reflectors. What do you get
> > when
> > > > you run troubleshoot-irlp?
> > > >
> > > > As repeater: troubleshoot-irlp
> > > > Mick - W7CAT
> > > > Node 3464
> > > >
> > > > ----- Original Message -----
> > > > From: Bob Redoutey N5KF
> > > > To: IRLP@irlp.groups.io
> > > > Sent: Friday, January 10, 2020 05:48:43 PM
> > > > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> > > >
> > > > > I did the easy solution, went with a bridge, but all I could find
> > was
> > > > "AC
> > > > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > > > connect to reflectors, but not getting any replies. The router has
> > only
> > > > 2
> > > > > options, TCP or UDP. No SSH. DMZ is available. When the node boots
> > up it
> > > > > says connected IRLP and Echolink.
> > > > >
> > > > > Any suggestions? Maybe it's working and nobody is talking?
> > > > >
> > > > > Bob N5KF
> > > > > Node 3437
> > > > > Georgetown TX
> > > > >
> > > > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > > > >
> > > > > > Alternately, you can just add the SSID and Preshared Key info into
> > the
> > > > > > interfaces file and not bother with wpa_supplicant now:
> > > > > >
> > > > > > allow-hotplug wlan0
> > > > > > iface wlan0 inet static
> > > > > > address 10.1.1.31
> > > > > > netmask 255.255.255.0
> > > > > > gateway 10.1.1.1
> > > > > > wpa-ssid NameOfYourWiFiNetwork
> > > > > > wpa-psk SuperSecretWifiPassword
> > > > > >
> > > > > > If you use a USB Wifi that is supported in Linux, it should be
> > just
> > > > plug
> > > > > > and play. By default on an IRLP install it will come up as wlan0
> > if
> > > > > > recognized.
> > > > > >
> > > > > > Plug it in, then run
> > > > > >
> > > > > > dmesg
> > > > > >
> > > > > > and look at the last few lines. Any errors should show up there.
> > > > > >
> > > > > > Dave Cameron
> > > > > >
> > > > > >
> > > > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > > > Bob Redoutey N5KF wrote:
> > > > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > > > Cameron
> > > > > > >> put together for years. If I add the USB WiFi, will it
> > > > automatically
> > > > > > >> configure to the new IP address? Or do I need to get into the
> > > > > > >> computer setup? I know I need to open ports on the new
> > Router/WiFi
> > > > > > setup.
> > > > > > >
> > > > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the
> > name
> > > > of
> > > > > > > the new interface (probably wlan0 but maybe something like
> > wlp1s0,
> > > > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > > > /etc/network/interfaces somewhat like:
> > > > > > >
> > > > > > > allow-hotplug wlan0
> > > > > > > iface wlan0 inet static
> > > > > > > address 10.1.1.31
> > > > > > > netmask 255.255.255.0
> > > > > > > gateway 10.1.1.1
> > > > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > > > >
> > > > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > > > something like:
> > > > > > >
> > > > > > > network={
> > > > > > > ssid="NameOfYourWiFiNetwork"
> > > > > > > psk="SuperSecretWifiPassword"
> > > > > > > }
> > > > > > >
> > > > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff,
> > but
> > > > if
> > > > > > > I recall, IRLP install disables this.
> > > > > > >
> > > > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your
> > WiFi
> > > > > > > network and want to scan.
> > > > > > >
> > > > > > >
> > > > > > > Nick VA3NNW
> > > > > > >
> > > > > > > --
> > > > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > > > use Std::Disclaimer;sig@...
> > > > > > > Vitamin C deficiency is apauling
> > > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > --
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Yes, it does have the DMZ option.

No, I don't have the model #, maybe Altice One.

Thing that was strange was that the ports were listed under only one IP address,  probably not the IRLP device, but couldn't figure out how to open up for all IP addresses.

Bob N5KF 
Node 3437

On Fri, Jan 10, 2020, 8:34 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

Sorry, I don't know that router, or all that many routers. I have looked some on google. A couple of things that I did find:

"To enable port forwarding on your system you will need to make “port rules” in your router to allow select traffic from the internet to allow access to devices on your network. ..."

"If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware. Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER It's Very Limited. If You Want Full Control Over Network AlticeOne is NOT: For YOU! Get Legacy Instead Where Can Use Own Router!"

Do you have a model number for your router?

Also, can you set up your node for DMZ?

Mick - W7CAT
Node 3464


----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:08:23 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Thank you Mick. Yes, I get errors related to DNS not setup correctly.
>
> Also TCP Port 15425 not forwarding correctly.
>
> UDP Error, all ports not forwarded correctly.
>
> Outbound Ports Correct.
>
> Everything else passed.
>
> So, it sounds like I didn't set up the router correctly...it was confusing.
>
> It's a Altice (Suddenlink)
>
> Familiar with it?
>
> Might have to reboot something, as it (the router) won't come up now!
>
> Thanks for the trouble shooting so far.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > That is one of the reasons for the echo reflectors. What do you get when
> > you run troubleshoot-irlp?
> >
> > As repeater: troubleshoot-irlp
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 05:48:43 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > I did the easy solution, went with a bridge, but all I could find was
> > "AC
> > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > connect to reflectors, but not getting any replies. The router has only
> > 2
> > > options, TCP or UDP. No SSH. DMZ is available. When the node boots up it
> > > says connected IRLP and Echolink.
> > >
> > > Any suggestions? Maybe it's working and nobody is talking?
> > >
> > > Bob N5KF
> > > Node 3437
> > > Georgetown TX
> > >
> > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > >
> > > > Alternately, you can just add the SSID and Preshared Key info into the
> > > > interfaces file and not bother with wpa_supplicant now:
> > > >
> > > > allow-hotplug wlan0
> > > > iface wlan0 inet static
> > > > address 10.1.1.31
> > > > netmask 255.255.255.0
> > > > gateway 10.1.1.1
> > > > wpa-ssid NameOfYourWiFiNetwork
> > > > wpa-psk SuperSecretWifiPassword
> > > >
> > > > If you use a USB Wifi that is supported in Linux, it should be just
> > plug
> > > > and play. By default on an IRLP install it will come up as wlan0 if
> > > > recognized.
> > > >
> > > > Plug it in, then run
> > > >
> > > > dmesg
> > > >
> > > > and look at the last few lines. Any errors should show up there.
> > > >
> > > > Dave Cameron
> > > >
> > > >
> > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > Bob Redoutey N5KF wrote:
> > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > Cameron
> > > > >> put together for years. If I add the USB WiFi, will it
> > automatically
> > > > >> configure to the new IP address? Or do I need to get into the
> > > > >> computer setup? I know I need to open ports on the new Router/WiFi
> > > > setup.
> > > > >
> > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the name
> > of
> > > > > the new interface (probably wlan0 but maybe something like wlp1s0,
> > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > /etc/network/interfaces somewhat like:
> > > > >
> > > > > allow-hotplug wlan0
> > > > > iface wlan0 inet static
> > > > > address 10.1.1.31
> > > > > netmask 255.255.255.0
> > > > > gateway 10.1.1.1
> > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > >
> > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > something like:
> > > > >
> > > > > network={
> > > > > ssid="NameOfYourWiFiNetwork"
> > > > > psk="SuperSecretWifiPassword"
> > > > > }
> > > > >
> > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff, but
> > if
> > > > > I recall, IRLP install disables this.
> > > > >
> > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your WiFi
> > > > > network and want to scan.
> > > > >
> > > > >
> > > > > Nick VA3NNW
> > > > >
> > > > > --
> > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > use Std::Disclaimer;sig@...
> > > > > Vitamin C deficiency is apauling
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

Sorry, I don't know that router, or all that many routers. I have looked some on google. A couple of things that I did find:

"To enable port forwarding on your system you will need to make “port rules” in your router to allow select traffic from the internet to allow access to devices on your network. ..."

"If You Ever Had Their "Smart Router" With Legacy It's Similar Firmware. Meaning You Can Do Port Forwarding, LAN IP Assignments, DMZ, etc. HOWEVER It's Very Limited. If You Want Full Control Over Network AlticeOne is NOT: For YOU! Get Legacy Instead Where Can Use Own Router!"

Do you have a model number for your router?

Also, can you set up your node for DMZ?

Mick - W7CAT
Node 3464


----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 07:08:23 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> Thank you Mick. Yes, I get errors related to DNS not setup correctly.
>
> Also TCP Port 15425 not forwarding correctly.
>
> UDP Error, all ports not forwarded correctly.
>
> Outbound Ports Correct.
>
> Everything else passed.
>
> So, it sounds like I didn't set up the router correctly...it was confusing.
>
> It's a Altice (Suddenlink)
>
> Familiar with it?
>
> Might have to reboot something, as it (the router) won't come up now!
>
> Thanks for the trouble shooting so far.
>
> Bob N5KF
> Node 3437
>
> On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association
> (TARRA) wrote:
>
> > That is one of the reasons for the echo reflectors. What do you get when
> > you run troubleshoot-irlp?
> >
> > As repeater: troubleshoot-irlp
> > Mick - W7CAT
> > Node 3464
> >
> > ----- Original Message -----
> > From: Bob Redoutey N5KF
> > To: IRLP@irlp.groups.io
> > Sent: Friday, January 10, 2020 05:48:43 PM
> > Subject: Re: [IRLP] Wired to Wireless on AT Computer
> >
> > > I did the easy solution, went with a bridge, but all I could find was
> > "AC
> > > Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> > > connect to reflectors, but not getting any replies. The router has only
> > 2
> > > options, TCP or UDP. No SSH. DMZ is available. When the node boots up it
> > > says connected IRLP and Echolink.
> > >
> > > Any suggestions? Maybe it's working and nobody is talking?
> > >
> > > Bob N5KF
> > > Node 3437
> > > Georgetown TX
> > >
> > > On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
> > >
> > > > Alternately, you can just add the SSID and Preshared Key info into the
> > > > interfaces file and not bother with wpa_supplicant now:
> > > >
> > > > allow-hotplug wlan0
> > > > iface wlan0 inet static
> > > > address 10.1.1.31
> > > > netmask 255.255.255.0
> > > > gateway 10.1.1.1
> > > > wpa-ssid NameOfYourWiFiNetwork
> > > > wpa-psk SuperSecretWifiPassword
> > > >
> > > > If you use a USB Wifi that is supported in Linux, it should be just
> > plug
> > > > and play. By default on an IRLP install it will come up as wlan0 if
> > > > recognized.
> > > >
> > > > Plug it in, then run
> > > >
> > > > dmesg
> > > >
> > > > and look at the last few lines. Any errors should show up there.
> > > >
> > > > Dave Cameron
> > > >
> > > >
> > > > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > > > Bob Redoutey N5KF wrote:
> > > > >> Yes, adding USB WiFi would be easy. My question is...what is
> > > > >> involved? No, it's not a ancient node. It's the AT style Dave
> > Cameron
> > > > >> put together for years. If I add the USB WiFi, will it
> > automatically
> > > > >> configure to the new IP address? Or do I need to get into the
> > > > >> computer setup? I know I need to open ports on the new Router/WiFi
> > > > setup.
> > > > >
> > > > > I assume you'd log in, you'd look at "ifconfig -a" to find the name
> > of
> > > > > the new interface (probably wlan0 but maybe something like wlp1s0,
> > > > > almost certainly begins "w" anyway), then you'd edit it into
> > > > > /etc/network/interfaces somewhat like:
> > > > >
> > > > > allow-hotplug wlan0
> > > > > iface wlan0 inet static
> > > > > address 10.1.1.31
> > > > > netmask 255.255.255.0
> > > > > gateway 10.1.1.1
> > > > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > > > >
> > > > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > > > something like:
> > > > >
> > > > > network={
> > > > > ssid="NameOfYourWiFiNetwork"
> > > > > psk="SuperSecretWifiPassword"
> > > > > }
> > > > >
> > > > > USUALLY Linux would just autoconfigure it using DHCP and stuff, but
> > if
> > > > > I recall, IRLP install disables this.
> > > > >
> > > > > "sudo iwlist wlan0 scan" if you're not sure of the name of your WiFi
> > > > > network and want to scan.
> > > > >
> > > > >
> > > > > Nick VA3NNW
> > > > >
> > > > > --
> > > > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > > > use Std::Disclaimer;sig@...
> > > > > Vitamin C deficiency is apauling
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > --
> >
> >
> >
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

Thank you Mick. Yes, I get errors related to DNS not setup correctly. 

Also TCP Port 15425 not forwarding correctly. 

UDP Error, all ports not forwarded correctly.

Outbound Ports Correct.

Everything else passed.

So, it sounds like I didn't set up the router correctly...it was confusing. 

It's a Altice (Suddenlink)

Familiar with it?

Might have to reboot something,  as it (the router) won't come up now!

Thanks for the trouble shooting so far.

Bob N5KF 
Node 3437

On Fri, Jan 10, 2020, 7:40 PM Teton Amateur Radio Repeater Association (TARRA) <tarra@...> wrote:

That is one of the reasons for the echo reflectors. What do you get when you run troubleshoot-irlp?

As repeater: troubleshoot-irlp

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 05:48:43 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> I did the easy solution, went with a bridge, but all I could find was "AC
> Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> connect to reflectors, but not getting any replies. The router has only 2
> options, TCP or UDP. No SSH. DMZ is available. When the node boots up it
> says connected IRLP and Echolink.
>
> Any suggestions? Maybe it's working and nobody is talking?
>
> Bob N5KF
> Node 3437
> Georgetown TX
>
> On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
>
> > Alternately, you can just add the SSID and Preshared Key info into the
> > interfaces file and not bother with wpa_supplicant now:
> >
> > allow-hotplug wlan0
> > iface wlan0 inet static
> > address 10.1.1.31
> > netmask 255.255.255.0
> > gateway 10.1.1.1
> > wpa-ssid NameOfYourWiFiNetwork
> > wpa-psk SuperSecretWifiPassword
> >
> > If you use a USB Wifi that is supported in Linux, it should be just plug
> > and play. By default on an IRLP install it will come up as wlan0 if
> > recognized.
> >
> > Plug it in, then run
> >
> > dmesg
> >
> > and look at the last few lines. Any errors should show up there.
> >
> > Dave Cameron
> >
> >
> > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > Bob Redoutey N5KF wrote:
> > >> Yes, adding USB WiFi would be easy. My question is...what is
> > >> involved? No, it's not a ancient node. It's the AT style Dave Cameron
> > >> put together for years. If I add the USB WiFi, will it automatically
> > >> configure to the new IP address? Or do I need to get into the
> > >> computer setup? I know I need to open ports on the new Router/WiFi
> > setup.
> > >
> > > I assume you'd log in, you'd look at "ifconfig -a" to find the name of
> > > the new interface (probably wlan0 but maybe something like wlp1s0,
> > > almost certainly begins "w" anyway), then you'd edit it into
> > > /etc/network/interfaces somewhat like:
> > >
> > > allow-hotplug wlan0
> > > iface wlan0 inet static
> > > address 10.1.1.31
> > > netmask 255.255.255.0
> > > gateway 10.1.1.1
> > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > >
> > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > something like:
> > >
> > > network={
> > > ssid="NameOfYourWiFiNetwork"
> > > psk="SuperSecretWifiPassword"
> > > }
> > >
> > > USUALLY Linux would just autoconfigure it using DHCP and stuff, but if
> > > I recall, IRLP install disables this.
> > >
> > > "sudo iwlist wlan0 scan" if you're not sure of the name of your WiFi
> > > network and want to scan.
> > >
> > >
> > > Nick VA3NNW
> > >
> > > --
> > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > use Std::Disclaimer;sig@...
> > > Vitamin C deficiency is apauling
> > >
> >
> >
> >
> >
> >
>
>
>
>
--

Re: No audio out

Teton Amateur Radio Repeater Association (TARRA)
 

What do you get when you run troubleshoot-irlp?

As repeater: troubleshoot-irlp

Mick - W7CAT
Node 3464

----- Original Message -----
From: David Snow Sr
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 06:05:12 PM
Subject: [IRLP] No audio out

> Any one have this problem I can connect to a node but no one can hear me so went to node 9999 to see if my voice would come through but it did not so I unplugged the Pi to reset it but after it came back up still the problem is there . The node i'm having the problem with is (node 3209) I'm thinking maybe the Pi is bad ?
>
> Thanks for any help out there
> David Snow KD6RGX
>
>
>
>
--

Re: Wired to Wireless on AT Computer

Teton Amateur Radio Repeater Association (TARRA)
 

That is one of the reasons for the echo reflectors. What do you get when you run troubleshoot-irlp?

As repeater: troubleshoot-irlp

Mick - W7CAT
Node 3464

----- Original Message -----
From: Bob Redoutey N5KF
To: IRLP@irlp.groups.io
Sent: Friday, January 10, 2020 05:48:43 PM
Subject: Re: [IRLP] Wired to Wireless on AT Computer

> I did the easy solution, went with a bridge, but all I could find was "AC
> Line" one. I opened IRLP/Echolink ports on the new router. I seem to
> connect to reflectors, but not getting any replies. The router has only 2
> options, TCP or UDP. No SSH. DMZ is available. When the node boots up it
> says connected IRLP and Echolink.
>
> Any suggestions? Maybe it's working and nobody is talking?
>
> Bob N5KF
> Node 3437
> Georgetown TX
>
> On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP wrote:
>
> > Alternately, you can just add the SSID and Preshared Key info into the
> > interfaces file and not bother with wpa_supplicant now:
> >
> > allow-hotplug wlan0
> > iface wlan0 inet static
> > address 10.1.1.31
> > netmask 255.255.255.0
> > gateway 10.1.1.1
> > wpa-ssid NameOfYourWiFiNetwork
> > wpa-psk SuperSecretWifiPassword
> >
> > If you use a USB Wifi that is supported in Linux, it should be just plug
> > and play. By default on an IRLP install it will come up as wlan0 if
> > recognized.
> >
> > Plug it in, then run
> >
> > dmesg
> >
> > and look at the last few lines. Any errors should show up there.
> >
> > Dave Cameron
> >
> >
> > On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> > > Bob Redoutey N5KF wrote:
> > >> Yes, adding USB WiFi would be easy. My question is...what is
> > >> involved? No, it's not a ancient node. It's the AT style Dave Cameron
> > >> put together for years. If I add the USB WiFi, will it automatically
> > >> configure to the new IP address? Or do I need to get into the
> > >> computer setup? I know I need to open ports on the new Router/WiFi
> > setup.
> > >
> > > I assume you'd log in, you'd look at "ifconfig -a" to find the name of
> > > the new interface (probably wlan0 but maybe something like wlp1s0,
> > > almost certainly begins "w" anyway), then you'd edit it into
> > > /etc/network/interfaces somewhat like:
> > >
> > > allow-hotplug wlan0
> > > iface wlan0 inet static
> > > address 10.1.1.31
> > > netmask 255.255.255.0
> > > gateway 10.1.1.1
> > > wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
> > >
> > > ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> > > something like:
> > >
> > > network={
> > > ssid="NameOfYourWiFiNetwork"
> > > psk="SuperSecretWifiPassword"
> > > }
> > >
> > > USUALLY Linux would just autoconfigure it using DHCP and stuff, but if
> > > I recall, IRLP install disables this.
> > >
> > > "sudo iwlist wlan0 scan" if you're not sure of the name of your WiFi
> > > network and want to scan.
> > >
> > >
> > > Nick VA3NNW
> > >
> > > --
> > > "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> > > use Std::Disclaimer;sig@...
> > > Vitamin C deficiency is apauling
> > >
> >
> >
> >
> >
> >
>
>
>
>
--

No audio out

David Snow Sr
 

Any one have this problem I can connect to a node but no one can hear me so went to node 9999 to see if my voice would come through but it did not so I unplugged the Pi to reset it but after it came back up still the problem is there . The node i'm having the problem with is (node 3209) I'm thinking maybe the Pi is bad ?

Thanks for any help out there
David Snow KD6RGX

Re: new crontab file is missing newline before EOF, can't install.

Charlie Wa2gug
 

Thanks Dave, will do..


Charlie wa2gug
ARRL FIELD INSTRUCTOR, VE



-------- Original message --------
From "Dave Parks - WB8ODF via Groups.Io" <wb8odf@...>
Date: 01/10/2020 16:17 (GMT-05:00)
To IRLP@irlp.groups.io
Subject Re: [IRLP] new crontab file is missing newline before EOF, can't install.


Charlie,

You can go to my web page (wb8odf.com) and download "filefix.tgz" this will fix any problems you have editing Linux files on you window machine and uploading them. I believe it makes sure your last line is a NewLine as well.

Good luck


>< Dave Parks ><
WB8ODF@...
http://wb8odf.com



On Friday, January 10, 2020, 1:16:44 PM EST, Charlie Wa2gug <wa2gug@...> wrote:


I was looking at wrong file. I added the carriage return at the end of the file, saved it, tried again same error.

On 1/10/2020 12:10, k9dc wrote:
What file are you looking at and how are you looking at it?  It should just be text.

'crontab -l’ to list it; ‘crontab -e’ to edit

-k9dc
 

On Jan 10, 2020, at 11:58, Charlie Wa2gug <wa2gug@...> wrote:

Dave thanks for reply. I tried looking at the file with an editor. It is unreadable.  To me it looks curopt. 
Can it be regenerated?


Charlie wa2gug
ARRL FIELD INSTRUCTOR, VE



-------- Original message --------
From k9dc <Dave@...> 
Date: 01/10/2020 11:19 (GMT-05:00) 
To IRLP@irlp.groups.io 
Subject Re: [IRLP] new crontab file is missing newline before EOF, can't install. 



Not worth re-installing over. The error message you received is pretty clear what the problem is.

new crontab file is missing newline before EOF, can't install.
Simply make sure the last character in the file is a NEWLINE, aka a <return> or <enter>.  The crontab file must end with <return> <EOF>.  If there is anything other than a <return> at the end of that file, it will be rejected by the OS.   

-k9dc


    
-- 
Charles L. Alfano
WA2GUG
ARRL VE, Instructor

Re: Wired to Wireless on AT Computer

Bob Redoutey N5KF
 

I did the easy solution, went with a bridge, but all I could find was "AC Line" one. I opened IRLP/Echolink ports on the new router. I seem to connect to reflectors, but not getting any replies. The router has only 2 options, TCP or UDP. No SSH. DMZ is available. When the node boots up it says connected IRLP and Echolink.

Any suggestions? Maybe it's working and nobody is talking?

Bob N5KF 
Node 3437
Georgetown TX 

On Sun, Jan 5, 2020, 9:48 PM David Cameron - IRLP <dcameron@...> wrote:
Alternately, you can just add the SSID and Preshared Key info into the
interfaces file and not bother with wpa_supplicant now:

allow-hotplug wlan0
iface wlan0 inet static
         address 10.1.1.31
         netmask 255.255.255.0
         gateway 10.1.1.1
         wpa-ssid NameOfYourWiFiNetwork
         wpa-psk SuperSecretWifiPassword

If you use a USB Wifi that is supported in Linux, it should be just plug
and play. By default on an IRLP install it will come up as wlan0 if
recognized.

Plug it in, then run

dmesg

and look at the last few lines. Any errors should show up there.

Dave Cameron


On 05/01/2020 7:15 p.m., Nosey Nick VA3NNW wrote:
> Bob Redoutey N5KF wrote:
>> Yes, adding USB WiFi would be easy. My question is...what is
>> involved? No, it's not a ancient node. It's the AT style Dave Cameron
>> put together for years. If I add the USB WiFi, will it automatically
>> configure to the new IP address? Or do I need to get into the
>> computer setup? I know I need to open ports on the new Router/WiFi setup.
>
> I assume you'd log in, you'd look at "ifconfig -a" to find the name of
> the new interface (probably wlan0 but maybe something like wlp1s0,
> almost certainly begins "w" anyway), then you'd edit it into
> /etc/network/interfaces somewhat like:
>
> allow-hotplug wlan0
> iface wlan0 inet static
>         address 10.1.1.31
>         netmask 255.255.255.0
>         gateway 10.1.1.1
>         wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
>
> ... and /etc/wpa_supplicant/wpa_supplicant.conf would include
> something like:
>
> network={
>         ssid="NameOfYourWiFiNetwork"
>         psk="SuperSecretWifiPassword"
> }
>
> USUALLY Linux would just autoconfigure it using DHCP and stuff, but if
> I recall, IRLP install disables this.
>
> "sudo iwlist wlan0 scan" if you're not sure of the name of your WiFi
> network and want to scan.
>
>
> Nick VA3NNW
>
> --
> "Nosey" Nick Waterman, VA3NNW/G7RZQ, K2 #5209.
> use Std::Disclaimer;sig@...
> Vitamin C deficiency is apauling
>